- 您現在的位置：買賣IC網 > PDF目錄371181 > TDA4780 (NXP SEMICONDUCTORS) RGB video processor with automatic cut-off control and gamma adjust PDF資料下載
參數資料
| 型號： | TDA4780 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 消費家電 |
| 英文描述： | RGB video processor with automatic cut-off control and gamma adjust |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PDIP28 |
| 封裝： | 0.600 INCH, PLASTIC, DIP-28 |
| 文件頁數： | 7/44頁 |
| 文件大?。?/td> | 321K |
| 代理商： | TDA4780 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
1997 Feb 06
7
Philips Semiconductors
Preliminary specification
RGB video processor with automatic
cut-off control and gamma adjust
TDA4780
FUNCTIONAL DESCRIPTION
Signal input stages
The TDA4780 contains 3 sets of input signal stages for:
1.
Luminance/colour-difference signals:
a) Y: 0.45 V (p-p) VBS or 1.43 V (p-p) VBS,
selectable via I
2
C-bus.
b)
(R
Y): 1.05 V (p-p).
c)
(B
Y): 1.33 V (p-p).
The capacitively coupled signals are matrixed to
RGB signals by either a PAL/SECAM or NTSC matrix
(selected via I
2
C-bus).
2.
(RGB)
1
signals (0.7 V (p-p) VB), capacitively coupled
(e.g. from external source).
3.
(RGB)
2
signals (0.7 V (p-p) VB), capacitively coupled
(e.g. videotext, OSD).
All input signals are clamped in order to have the same
black levels at the signal switch input. Displayed signals
must be synchronous with the sandcastle pulse.
Signal switches
Both fast signal switches can be operated by switching
pins (e.g. SCART facilities) or set via the I
2
C-bus. With the
pin FSW
1
the Y-CD signals or the (RGB)
1
signals can be
selected, with pin FSW
2
the above selected signals or the
(RGB)
2
signals are enabled. During the vertical and
horizontal blanking time an artificial black level equal to the
clamped black level is inserted in order to clip off the sync
pulse of the luminance signal and to suppress hum during
the cut-off measurement time and eliminate noise during
these intervals.
Saturation, contrast and brightness adjust
Saturation, contrast and brightness adjusts are controlled
via the I
2
C-bus and act on Y, CD as well as on RGB input
signals. Gamma acts on the luminance content of the input
signals.
Gamma adjust
The gamma adjust stage has a non-linear transmission
characteristic according to the formula y = x
gamma
, where x
represents the input and y the output signal. If gamma is
smaller than unity, the lower parts of the signal are
amplified with higher gain.
Adaptive black (ADBL)
The adaptive black stage detects the lowest voltage of the
luminance component of the internal RGB signals during
the scanning time and shifts it to the nominal black level.
In order to keep the nominal white level the contrast is
increased simultaneously.
Blue stretch (BLST)
The blue stretch channel gets additional amplification if the
blue signal is greater than 80% of the nominal signal
amplitude. In the event the white point is shifted towards
higher colour temperature so that white parts of a picture
seem to be brighter.
Measurement pulse and blanking stage
During the vertical and horizontal blanking time and the
measurement period the signals are blanked to an ultra
black level, so the leakage current of the picture tube can
be measured and automatically compensated for.
During the cut-off measurement lines (one line period for
each R, G or B) the output signal levels are at cut-off
measurement level.
The vertical blanking period is timed by the sandcastle
pulse. The measurement pulses (leakage, R, G and B) are
triggered by the negative going edge of the vertical pulse
of the sandcastle pulse and start after the following
horizontal pulse.
The IC is prepared for 2f
H
(32 kHz) application.
Output amplifier and white adjust potentiometer
The RGB signals are amplified to nominal 2 V (p-p), the
DC-levels are shifted according to cut-off control.
The nominal signal amplitude can be varied by
±
50% by
the white point adjustment via the I
2
C-bus (individually for
RGB respect).
相關PDF資料 |
PDF描述 |
|---|---|
| TDA4864AJ | Vertical deflection booster |
| TDA4864J | Vertical deflection booster |
| TDA4867J | Full bridge current driven vertical deflection booster |
| TDA4867 | Full bridge current driven vertical deflection booster |
| TDA6107JF | Triple video output amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA4800 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Vertical deflection circuit for monitor applications |
| TDA4810 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SYNC PROCESSOR AND HORIZONTAL DRIVE FOR MONITORS |
| TDA4814 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:Power Factor Controller IC for High Power Factor and Active Harmonic Filter |
| TDA4814A | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:Power Factor Controller IC for High Power Factor and Active Harmonic Filter |
| TDA4817 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:Power Factor Controller IC for High Power Factor and Active Harmonic Filtering |
發布緊急采購，3分鐘左右您將得到回復。