- 您現在的位置：買賣IC網 > PDF目錄373621 > TDA7340G (意法半導體) AUDIO SIGNAL PROCESSOR PDF資料下載
參數資料
| 型號： | TDA7340G |
| 廠商： | 意法半導體 |
| 英文描述： | AUDIO SIGNAL PROCESSOR |
| 中文描述： | 音頻信號處理器 |
| 文件頁數： | 17/27頁 |
| 文件大?。?/td> | 205K |
| 代理商： | TDA7340G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
1.1 TriggerPath
The incoming MPX signal is highpass-filtered,
amplified and rectified(block RECT-PEAK).
The second order highpass-filterhas a corner-fre-
quency of 140KHz.
The rectifier signal, RECT, is used to generate by
peak-rectification a signal called PEAK, which is
available at the PEAK pin.
Also noise with a frequency >100KHz increases
the PEAK voltage. The value of the PEAKvoltage
influences the trigger threshold voltage Vth (block
ATC).
Both signals, RECT and PEAK+Vth are fed to a
comparator (block PEAK-COMP) which outputs a
sawtooth-shapedwaveform at the TBLANK pin. A
second comparator (block BLANK-COMP) forms
the internal blanking duration of 40
μ
s.
The noise blanker is supplied by his own biasing
circuit (block BIAS-MONO).
1.2 Automatic Noise Controlled Threshold
Control (ATC)
The are two independent possibilities for pro-
grammingthe triggerthreshold:
a)the minimum threshold in 8 steps (bits D6, D5
of the STD-byte and bit D5 of the SPKR_LF
byte)
b)and the noise adjusted threshold in 4 steps
(bits D6, D5of the SPKR_LFbyte, (seefig.5)
The minimum threshold is used in combination
with a goodMPX signalwithout any noise.
The sensitivityin this operationis high, depending
only on the programmed ”minimum trigger thresh-
old”, bits NTB of the noise blanker byte 1.
It is independentof the PEAK voltage.
If the MPX signal is noisy (low fieldstrength) the
PEAK signal increases due to the higher noise,
which is also rectified(see part 1.1).
With increasing of the PEAK voltage the trigger
threshold voltage increases, too. This particular
gain is programmablein 4 steps(see fig.2).
1.3 Automatic Threshold Control by the
Stereoblendvoltage (ATC-SB)
Besides the noise controlled threshold adjustment
there is an additionalpossibility for influencingthe
trigger. It is controlled by the difference between
Vsb and Vr, similar to the Stereoblend. The rea-
son for implementing such a second control will
be explainedin the following:
The point where the MPX signal starts to become
noisy is fixed by the RF part. Therefore also the
starting point of the normal noise controlled trig-
ger adjustmentis fixed (fig.6).
But in some cases the behaviour of the noise-
blanker can be improved by increasing the
threshold even in a region of higher fieldstrength,
for the MPX signal often shows distortion in this
range.
Because of the overlap of this range and the
range of the stereo/mono transition it can be con-
trolled by Vsb and Vr.
This threshold increase is programmable in 3
steps or switchedoff (seefig.6).
1.4 OverDeviation Detector (MPX-RECT)
Sometimes when listening to stations with a
higher deviation than 75KHz the noiseblanker
triggerson the high frequencymodulation.
To avoid this blanking, which causes noise in the
output signal, the noiseblanker offers a deviation-
dependentthreshold adjustment.
By rectifying the MPX signal a further signal rep-
resenting the actual deviation is obtained. It is
used to increase the PEAKvoltage.
Offset and gain of this circuit are programmablein
3 steps (the first step turns off the detector, see
fig.7).
1.5 BlendMode
Another possibility to avoid a disturbing triggering
on modulation is to use the spikes on the field-
strength signal (LEVELpin).
But in the range of higher fieldstrength the signal
saturates and no more spike detection is possi-
ble. For this reason the TDA7340G offers the
”BLEND MODE”. When ”BLEND MODE” is acti-
vated a smooth transition between the LEVEL-
and the MPX-signal is used to detect the spikes
either on LEVELor on MPX.
In the lower fieldstrength range mainly the
LEVEL-signal is used whereas in the higher
range mainly the MPX is used. This switching is
controlled also by the normal Stereoblend signal
to avoid additionalpins.
With ”BLEND MODE OFF” both signals are used
to detectspikes in thewhole fieldstrength range.
1.6 InputMode
The NB of TDA7340G offers two input modes.
The first one uses the internal trigger path and
optional the LEVEL input. But the TDA7340G of-
fers also an externaltrigger mode.
During this mode the internal MPX trigger path is
disabled whereas the high pass at the LEVEL pin
is bypassed.
By using an external highpass at the LEVEL-pin
one can adjust the NB’s behaviour to the desired
one.
TDA7340G
17/27
相關PDF資料 |
PDF描述 |
|---|---|
| TDA7340 | AUDIO SIGNAL PROCESSOR |
| TDA7340P | AUDIO SIGNAL PROCESSOR |
| TDA7342 | DIGITALLY CONTROLLED AUDIO PROCESSOR |
| TDA7343 | DIGITALLY CONTROLLED AUDIO PROCESSOR |
| TDA7343D | DIGITALLY CONTROLLED AUDIO PROCESSOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA7340P | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:AUDIO SIGNAL PROCESSOR |
| TDA7340S | 功能描述:音頻 DSP Audio Signal Proc RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube |
| TDA7342 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Digitally controlled audio processor |
| TDA7342_06 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Digitally controlled audio processor |
| TDA7342EQ2N | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Digitally controlled audio processor |
發布緊急采購，3分鐘左右您將得到回復。