- 您現在的位置：買賣IC網 > PDF目錄98220 > THS3091DDA (TEXAS INSTRUMENTS INC) 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 PDF資料下載
參數資料
| 型號： | THS3091DDA |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| 封裝： | GREEN, PLASTIC, SOP-8 |
| 文件頁數： | 15/37頁 |
| 文件大?。?/td> | 1078K |
| 代理商： | THS3091DDA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
SLOS423G – SEPTEMBER 2003 – REVISED OCTOBER 2008........................................................................................................................................ www.ti.com
farther from the device and may be shared among
signal
loss
intrinsic
to
a
doubly
terminated
several devices in the same area of the PC board.
transmission line is acceptable, implement a
matched
impedance
transmission
line
using
Careful selection and placement of external
microstrip or stripline techniques (consult an ECL
components
preserve
the
high-frequency
design handbook for microstrip and stripline layout
performance of the THS3091/5. Resistors should
techniques). A 50-
environment is not necessary
be a low reactance type. Surface-mount resistors
onboard,
and
in
fact,
a
higher
impedance
work best and allow a tighter overall layout. Again,
environment improves distortion as shown in the
keep their leads and PC board trace length as
distortion versus load plots. With a characteristic
short as possible. Never use wirebound type
board trace impedance based on board material
resistors in a high-frequency application. Because
and trace dimensions, a matching series resistor
the output pin and inverting input pins are the
into the trace from the output of the THS3091/5 is
most sensitive to parasitic capacitance, always
used as well as a terminating shunt resistor at the
position the feedback and series output resistors,
input of the destination device. Remember also
if any, as close as possible to the inverting input
that the terminating impedance is the parallel
pins and output pins. Other network components,
combination of the shunt resistor and the input
such as input termination resistors, should be
impedance of the destination device; this total
placed close to the gain-setting resistors. Even
effective impedance should be set to match the
with a low parasitic capacitance shunting the
trace impedance. If the 6-dB attenuation of a
external resistors, excessively high resistor values
doubly
terminated
transmission
line
is
can create significant time constants that can
unacceptable,
a
long
trace
can
be
series-
degrade performance. Good axial metal-film or
terminated at the source end only. Treat the trace
surface-mount resistors have approximately 0.2
as a capacitive load in this case. This does not
pF in shunt with the resistor. For resistor values >
preserve signal integrity as well as a doubly
2 k
, this parasitic capacitance can add a pole
terminated line. If the input impedance of the
and/or a zero that can effect circuit operation.
destination device is low, there is some signal
Keep
resistor
values
as
low
as
possible,
attenuation due to the voltage divider formed by
consistent with load-driving considerations.
the series output into the terminating impedance.
Connections to other wideband devices on the
Socketing a high-speed part like the THS3091/5 is
board may be made with short direct traces or
not recommended. The additional lead length and
through onboard transmission lines. For short
pin-to-pin capacitance introduced by the socket
connections, consider the trace and the input to
can create an extremely troublesome parasitic
the next device as a lumped capacitive load.
network which can make it almost impossible to
Relatively wide traces [0.05 inch (1,3 mm) to 0.1
achieve a smooth, stable frequency response.
inch (2,54 mm)] should be used, preferably with
Best
results
are
obtained
by
soldering
the
ground and power planes opened up around
THS3091/5 parts directly onto the board.
them. Estimate the total capacitive load and
determine if isolation resistors on the outputs are
necessary. Low parasitic capacitive loads (< 4 pF)
may not need an RS because the THS3091/5 are
nominally compensated to operate with a 2-pF
parasitic load. Higher parasitic capacitive loads
without an RS are allowed as the signal gain
increases
(increasing
the
unloaded
phase
margin). If a long trace is required, and the 6-dB
22
Copyright 2003–2008, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| THS3091DR | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS3091D | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS3091DRG4 | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS3091DG4 | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS3091DDARG3 | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS3091DDA | 制造商:Texas Instruments 功能描述:IC OP AMP CFB SMD 3091 HSOP8 |
| THS3091DDAG3 | 功能描述:高速運算放大器 Single Lo-Distort Current Feedback RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS3091DDAR | 功能描述:高速運算放大器 Single Lo-Distort Current Feedback RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS3091DDARG3 | 功能描述:高速運算放大器 Single Lo-Distort Current Feedback RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS3091DG4 | 功能描述:高速運算放大器 Single Lo-Distort Current Feedback RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。