參數資料
型號： TLC32040I
廠商： Texas Instruments, Inc.
英文描述： ANALOG INTERFACE CIRCUITS
中文描述： 模擬接口電路
文件頁數： 8/33頁
文件大?。?/td> 453K
代理商： TLC32040I
TLC32040C, TLC32040I, TLC32041C, TLC32041I
ANALOG INTERFACE CIRCUITS
SLAS014E – SEPTEMBER 1987 – REVISED MAY 1995
8
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
reset
A reset function is provided to initiate serial communications between the AIC and DSP and allow fast,
cost-effective testing during manufacturing. The reset function initializes all AIC registers, including the control
register. After a negative-going pulse on RESET, the AIC is initialized. This initialization allows normal serial port
communications activity to occur between AIC and DSP (see AIC DX data word format section).
loopback
This feature allows the user to test the circuit remotely. In loopback, OUT+ and OUT– are internally connected
to IN+ and IN–. Thus, the DAC bits (d15 to d2), which are transmitted to DX, can be compared with the ADC
bits (d15 to d2), which are received from DR. An ideal comparison would be that the bits on DR equal the bits
on DX. However, in practice there is some difference in these bits due to the ADC and DAC output offsets.
In loopback, if IN+ and N– are enabled, the external signals on IN+ and IN– are ignored. If AUX IN+ and AUX
IN– are enabled, the external signals on these terminals are added to the OUT+ and OUT– signals in loopback
operation.
The loopback feature is implemented with digital signal processor control by transmitting the appropriate serial
port bit to the control register (see AIC DX data word format section).
explanation of internal timing configuration
All of the internal timing of the AIC is derived from the high-frequency clock signal that drives the master clock
input. The shift clock signal, which strobes the serial port data between the AIC and DSP, is derived by dividing
the master clock input signal frequency by four.
SCF Clock Frequency
Master Clock Frequency
Contents of Counter A
2
Conversion Frequency
SCF Clock Frequency
Contents of Counter B
Shift Clock Frequency
Master Clock Frequency
4
TX counter A and TX counter B, which are driven by the master clock signal, determine the D/A conversion
timing. Similarly, RX counter A and RX counter B determine the A/D conversion timing. In order for the
switched-capacitor low-pass and band pass filters to meet their transfer function specifications, the frequency
of the clock inputs of the switched-capacitor filters must be 288 kHz. If the frequencies of the clock inputs are
not 288 kHz, the filter transfer function frequencies are scaled by the ratios of the clock frequencies to 288 kHz.
Thus, to obtain the specified filter responses, the combination of master clock frequency and TX counter A and
RX counter A values must yield 288-kHz switched-capacitor clock signals. These 288-kHz clock signals can
then be divided by the TX counter B and RX counter B to establish the D/A and A/D conversion timings.
TX counter A and TX counter B are reloaded every D/A conversion period, while RX counter A and RX counter
B are reloaded every A/D conversion period. The TX counter B and RX counter B are loaded with the values
in the TB and RB registers, respectively. Via software control, the TX counter A can be loaded with either the
TA register, the TA register less the TA’ register, or the TA register plus the TA’ register. By selecting the TA
register less the TA’ register option, the upcoming conversion timing will occur earlier by an amount of time that
equals TA’ times the signal period of the master clock. By selecting the TA register plus the TA’ register option,
the upcoming conversion timing will occur later by an amount of time that equals TA’ times the signal period of
the master clock. Thus, the D/A conversion timing can be advanced or retarded. An identical ability to alter the
A/D conversion timing is provided. In this case, however, the RX counter A can be programmed via software
control with the RA register, the RA register less the RA’ register, or the RA register plus the RA’ register.
相關PDF資料
PDF描述
TLC32041C ANALOG INTERFACE CIRCUITS
TLC32041CFN ANALOG INTERFACE CIRCUITS
TLC32041I ANALOG INTERFACE CIRCUITS
TLC32040M ANALOG INTERFACE CIRCUIT
TLC32040MFK ANALOG INTERFACE CIRCUIT
相關代理商/技術參數
參數描述
TLC32040IN 制造商:TI 制造商全稱:Texas Instruments 功能描述:ANALOG INTERFACE CIRCUITS
TLC32040M 制造商:TI 制造商全稱:Texas Instruments 功能描述:ANALOG INTERFACE CIRCUIT
TLC32040MFK 制造商:TI 制造商全稱:Texas Instruments 功能描述:ANALOG INTERFACE CIRCUIT
TLC32040MJ 制造商:TI 制造商全稱:Texas Instruments 功能描述:ANALOG INTERFACE CIRCUIT
TLC32041C 制造商:TI 制造商全稱:Texas Instruments 功能描述:ANALOG INTERFACE CIRCUITS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*