參數資料
型號： TLV1548MFK
廠商： TEXAS INSTRUMENTS INC
元件分類： ADC
英文描述： 8-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, CQCC20
封裝： CERAMIC, LCC-20
文件頁數： 36/36頁
文件大?。?/td> 676K
代理商： TLV1548MFK
TLV1544C, TLV1544I, TLV1548C, TLV1548I, TLV1548M
LOW-VOLTAGE 10-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 4/8 ANALOG INPUTS
SLAS139C – DECEMBER 1996 – REVISED JANUARY 1999
9
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
extended sampling, asynchronous start of sampling: CSTART operation
The extended sampling mode of operation programs the acquisition time (tACQ) of the sample-and-hold circuit.
This allows the analog inputs of the device to be directly interfaced to a wide range of input source impedances.
The extended sampling mode consumes higher power depending on the duration of the sampling period
chosen.
CSTART controls the sampling period and starts the conversion. The falling edge of CSTART initiates the
sampling period of a preset channel. The low time of CSTART controls the acquisition time of the input
sample-and-hold circuit. The sample is held on the rising edge of CSTART. Asserting CSTART causes the
converter to perform a new sample of the signal on the preset valid MUX channel (one of the eight) and discard
the current conversion result ready for output. Sampling continues as long as CSTART is active (negative). The
rising edge of CSTART ends the sampling cycle. The conversion cycle starts two internal system clocks after
the rising edge of CSTART.
Once the conversion is complete, the processor can initiate a normal I/O cycle to read the conversion result and
set the MUX address for the next conversion. Since the internal flag AsyncFlag is set high, this flag setting
indicates the cycle is an output cycle, so no conversion is performed during the cycle. The internal state machine
tests the AsyncFlag on the falling edge of CS. AsyncFlag is set high at the rising edge of CSTART, and it is reset
low at the rising edge of each CS. A conversion cycle follows a sampling cycle only if AsyncFlag is tested as
low at the falling edge of CS. As shown in Figure 2, an asynchronous I/O cycle can be removed by two
consecutive normal I/O cycles.
Table 4. TLV1544/1548 Hardware Configuration for Different Operating Modes
OPERATING MODES
CS
CSTART
AsyncFlag at CS
↓
ACTION
Normal sampling
Low
High
Low
Fixed 6 I/O CLK sampling, synchronous conversion follows
Normal I/O (read out only)
Low
High
No sampling, no conversion
Extended sampling
High
Low
N/A
Flexible sampling period controlled by CSTART,
asynchronous conversion follows
相關PDF資料
PDF描述
TLV1548MJ 8-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, CDIP20
TLV1548QDBREP 8-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20
TLV1548QDBRQ1 8-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20
TLV1548QDBRG4Q1 8-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20
TLV1549IDRG4 1-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8
相關代理商/技術參數
參數描述
TLV1548MFKB 制造商:TI 制造商全稱:Texas Instruments 功能描述:LOW-VOLTAGE 10-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL AND 4/8 ANALOG INPUTS
TLV1548MJ 制造商:TI 制造商全稱:Texas Instruments 功能描述:LOW-VOLTAGE 10-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL AND 4/8 ANALOG INPUTS
TLV1548MJB 制造商:Rochester Electronics LLC 功能描述:- Bulk
TLV1548-Q1 制造商:TI 制造商全稱:Texas Instruments 功能描述:LOW-VOLTAGE 10-BIT ANALOG-TO-DIGITAL CONVERTER WITH SERIAL CONTROL AND 8 ANALOG INPUTS
TLV1548QDBREP 功能描述:模數轉換器 - ADC Lo Vltg 10B ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*