參數資料
型號： TLV320AIC10IPFB
廠商： TEXAS INSTRUMENTS INC
元件分類： 消費家電
英文描述： SPECIALTY CONSUMER CIRCUIT, PQFP48
封裝： GREEN, PLASTIC, TQFP-48
文件頁數： 21/57頁
文件大?。?/td> 454K
代理商： TLV320AIC10IPFB
3–2
3.2
Secondary Serial Communication
Secondary serial communication is used to read or write 16-bit words that program both the options and the circuit
configurations of the device. Register programming always occurs during secondary communication. Four primary
and secondary communication cycles are requested to program the four registers. If the default value for a particular
register is desired, then the register addressing can be omitted during secondary communications. The NOOP
command addresses a pseudo-register (register 0), and no register programming takes place during this secondary
communication. If secondary communication is desired for any device (either master or slave), then a secondary
communication must be requested for all devices, starting with the master. This results in a secondary frame-sync
(FS) for all devices. The NOOP command can be used for devices that do not need a secondary operation.
During a secondary communication, a register can be written to or read from. When writing to a register, DIN contains
the value to be written. The data returned on DOUT is + 0000000000000 (3-bit device address).
There are two methods of initiating a secondary communication, as illustrated in Figure 3–2:
Asserting a high level on FC (hardware request)
Asserting the LSB of the DIN 16-bit serial communication high while in the 15-bit mode (software request)
NOTE:The secondary communication request should not be asserted during the first two
samples after power up.
FC
(Hardware)
16-Bit Mode
(Control 1 Register, D0)
Internal TLV320AIC10
(LSB of DIN)
Secondary Request
Figure 3–2. Hardware and Software Secondary Communication Request
Pulling FC high causes the start of the secondary communications 128 or 256 SCLKs (see Figures 2–2 and 2–4) after
the start of the primary communication frame, depending on the number of devices in cascade.
The second method to initiate a secondary communication is asserting the LSB high. A software request is typically
used when the request resolution of the DAC channel is less than 16 bits. Then the least significant bit (D0) can be
used for secondary requests, as shown in Table 3–1. The request is made by placing the device in the 15-bit DAC
mode and making the LSB of DIN high. All cascading devices must be in 15-bit DAC mode, and set their LSBs to 1s
for requesting software secondary communication.
Table 3–1. Least Significant Bit Control Function
CONTROL BIT D0
CONTROL BIT FUNCTION
0
No operation (NOOP)
1
Secondary communication request
相關PDF資料
PDF描述
TLV320AIC10CGQE SPECIALTY CONSUMER CIRCUIT, PBGA80
TLV320AIC10IGQE SPECIALTY CONSUMER CIRCUIT, PBGA80
TLV320AIC10CGQER SPECIALTY CONSUMER CIRCUIT, PBGA80
TLV320AIC10IGQER SPECIALTY CONSUMER CIRCUIT, PBGA80
TLV320AIC11C SPECIALTY CONSUMER CIRCUIT, PQFP48
相關代理商/技術參數
參數描述
TLV320AIC10IPFBG4 功能描述:接口—CODEC 18-Bit Regstr Bus Trncvr W/3-St Otpt RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
TLV320AIC10PFB 制造商:TI 制造商全稱:Texas Instruments 功能描述:General-Purpose 3V to 5.5V 16-bit 22-KSPS DSP CODEC
TLV320AIC11 制造商:TI 制造商全稱:Texas Instruments 功能描述:General-Purpose Low-Voltage 1.1V to 3.6V/0 16-bit 22-KSPS DSP CODEC
TLV320AIC1103 制造商:TI 制造商全稱:Texas Instruments 功能描述:PCM CODEC
TLV320AIC1103EVM 功能描述:音頻 IC 開發工具 TLV320AIC1103 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*