參數資料
型號: TMS320C6711GJLA167
廠商: Texas Instruments, Inc.
元件分類: 數字信號處理
英文描述: FIXED-POINT DIGITAL SIGNAL PROCESSORS
中文描述: 定點數字信號處理器
文件頁數: 28/123頁
文件大?。?/td> 1205K
代理商: TMS320C6711GJLA167
www.ti.com
3.2.2
Memory Bus (Harvard Bus Architecture)
3.2.3
Peripheral Bus
3.2.4
Real-Time JTAG and Analysis
3.2.5
Flash
TMS320F2808, TMS320F2806
TMS320F2801, UCD9501
Digital Signal Processors
SPRS230F–OCTOBER 2003–REVISED SEPTEMBER 2005
As with many DSP type devices, multiple busses are used to move data between the memories and
peripherals and the CPU. The C28x memory bus architecture contains a program read bus, data read bus
and data write bus. The program read bus consists of 22 address lines and 32 data lines. The data read
and write busses consist of 32 address lines and 32 data lines each. The 32-bit-wide data busses enable
single cycle 32-bit operations. The multiple bus architecture, commonly termed "Harvard Bus", enables the
C28x to fetch an instruction, read a data value and write a data value in a single cycle. All peripherals and
memories attached to the memory bus will prioritize memory accesses. Generally, the priority of memory
bus accesses can be summarized as follows:
Highest:
Data Writes
Program Writes
Data Reads
Program Reads
Fetches
(Simultaneous data and program writes cannot occur on the memory bus.)
(Simultaneous data and program writes cannot occur on the memory bus.)
(Simultaneous program reads and fetches cannot occur on the memory bus.)
(Simultaneous program reads and fetches cannot occur on the memory bus.)
Lowest:
To enable migration of peripherals between various Texas Instruments (TI) DSP family of devices, the
280x devices adopt a peripheral bus standard for peripheral interconnect. The peripheral bus bridge
multiplexes the various busses that make up the processor Memory Bus into a single bus consisting of 16
address lines and 16 or 32 data lines and associated control signals. Two versions of the peripheral bus
are supported on the 280x. One version only supports 16-bit accesses (called peripheral frame 2). The
other version supports both 16- and 32-bit accesses (called peripheral frame 1).
The 280x implements the standard IEEE 1149.1 JTAG interface. Additionally, the 280x supports real-time
mode of operation whereby the contents of memory, peripheral and register locations can be modified
while the processor is running and executing code and servicing interrupts. The user can also single step
through non-time critical code while enabling time-critical interrupts to be serviced without interference.
The 280x implements the real-time mode in hardware within the CPU. This is a unique feature to the
280x, no software monitor is required. Additionally, special analysis hardware is provided which allows the
user to set hardware breakpoint or data/address watch-points and generate various user-selectable break
events when a match occurs.
The F2808 contains 64K x 16 of embedded flash memory, segregated into four 16K X 16 sectors. The
F2806 has 32K X 16 of embedded flash, segregated into four 8K X 16 sectors. The F2801/UCD9501
devices contain 16K X 16 of embedded Flash (four 4K X 16 sectors). All three devices also contain a
single 1K x 16 of OTP memory at address range 0x3D 7800 - 0x3D 7BFF. The user can individually
erase, program, and validate a flash sector while leaving other sectors untouched. However, it is not
possible to use one sector of the flash or the OTP to execute flash algorithms that erase/program other
sectors. Special memory pipelining is provided to enable the flash module to achieve higher performance.
The flash/OTP is mapped to both program and data space; therefore, it can be used to execute code or
store data information. Note that addresses 0x3F7FF0 - 0x3F7FF5 are reserved for data variables and
should not contain program code.
28
Functional Overview
相關PDF資料
PDF描述
TMS320C6711GJLA150 FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6711GJLA120 FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6711GJLA100 FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6711GJL167 FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6711GJL150 FIXED-POINT DIGITAL SIGNAL PROCESSORS
相關代理商/技術參數
參數描述
TMS320C6712CGDP150 制造商:Texas Instruments 功能描述:
TMS320C6712DGDP150 功能描述:數字信號處理器和控制器 - DSP, DSC Floating-Pt Dig Sig Proc RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320C6712DZDP150 功能描述:數字信號處理器和控制器 - DSP, DSC Floating-Pt Dig Sig Proc RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320C6712GFN100 功能描述:IC FLOATING POINT DSP 256-BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP(數字式信號處理器) 系列:TMS320C67x 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI,以太網,RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA,F(xiàn)CBGA 供應商設備封裝:431-FCPBGA(20x20) 包裝:托盤
TMS320C6713BGDP225 功能描述:數字信號處理器和控制器 - DSP, DSC Floating-Pt Dig Sig Processors RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT