參數資料
型號： TPA0202PWP
廠商： TEXAS INSTRUMENTS INC
元件分類： 音頻／視頻放大
英文描述： 2.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO24
封裝： GREEN, PLASTIC, HTSSOP-24
文件頁數： 29/45頁
文件大?。?/td> 1035K
代理商： TPA0202PWP
TPA0202
2-W STEREO AUDIO POWER AMPLIFIER
SLOS205B – FEBRUARY 1998 – REVISED DECEMBER 2000
35
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
SE/BTL operation
The ability of the TPA0202 to easily switch between BTL and SE modes is one of its most important cost saving
features. This feature eliminates the requirement for an additional headphone amplifier in applications where
internal stereo speakers are driven in BTL mode but external headphone or speakers must be accommodated.
Internal to the TPA0202, two separate amplifiers drive OUT+ and OUT–. The SE/BTL input (terminal 14)
controls the operation of the follower amplifier that drives LOUT– and ROUT– (terminals 10 and 15). When
SE/BTL is held low, the amplifier is on and the TPA0202 is in the BTL mode. When SE/BTL is held high, the OUT–
amplifiers are in a high output impedance state, which configures the TPA0202 as an SE driver from LOUT+
and ROUT+ (terminals 3 and 22). IDD is reduced by approximately one-half in SE mode. Control of the SE/BTL
input can be from a logic-level CMOS source or, more typically, from a resistor divider network as shown in
Figure 68.
MUX
RLINE IN
RHP IN
+
–
Bypass
SE/BTL
HP/LINE
Rm2
100 k
Rm1
100 k
VDD
COUTR
16
14
Rm3
1 k
+
–
ROUT – 15
ROUT+ 22
Left
Channel
20
21
0.1
F
Figure 68. TPA0202 Resistor Divider Network Circuit
Using a readily available 1/8-in. (3.5 mm) stereo headphone jack, the control switch is closed when no plug is
inserted. When closed the 100-k
/1-k divider pulls the SE/BTL input low. When a plug is inserted, the 1-k
resistor is disconnected and the SE/BTL input is pulled high. When the input goes high, the OUT– amplifier is
shutdown causing the speaker to mute (virtually open-circuits the speaker). The OUT+ amplifier then drives
through the output capacitor (CO) into the headphone jack.
As shown in the full feature application (Figure 63), the input MUX control can be tied to the SE/BTL input. The
benefits of doing this are described in the following input MUX operation section.
相關PDF資料
PDF描述
TPA0202PWPG4 2.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO24
TPA0202PWPRG4 2.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO24
TPA0211DGN 2 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8
TPA0211DGNR 2 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8
TPA0211DGNG4 2 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8
相關代理商/技術參數
參數描述
TPA0202PWPG4 功能描述:音頻放大器 2W Stereo A RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA0202PWPR 功能描述:音頻放大器 2W St Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA0202PWPRG4 功能描述:音頻放大器 2W St Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA0211 制造商:TI 制造商全稱:Texas Instruments 功能描述:2-W MONO AUDIO POWER AMPLIFIER
TPA0211_07 制造商:TI 制造商全稱:Texas Instruments 功能描述:2-W MONO AUDIO POWER AMPLIFIER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*