- 您現在的位置：買賣IC網 > PDF目錄2118 > TPA2016D2YZHT (Texas Instruments)IC AMP AUDIO PWR 2.8W D 16DSBGA PDF資料下載
參數資料
| 型號： | TPA2016D2YZHT |
| 廠商： | Texas Instruments |
| 文件頁數： | 13/39頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP AUDIO PWR 2.8W D 16DSBGA |
| 標準包裝： | 1 |
| 類型： | D 類 |
| 輸出類型： | 2 通道（立體聲） |
| 在某負載時最大輸出功率 x 通道數量： | 2.8W x 2 @ 4 歐姆 |
| 電源電壓： | 2.5 V ~ 5.5 V |
| 特點： | 差分輸入，I²C，短路和熱保護，關機，音量控制 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 16-DSBGA（2x2） |
| 封裝/外殼： | 16-UFBGA，DSBGA |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 876 (CN2011-ZH PDF) |
| 配用： | 296-31088-ND - EVAL MODULE FOR TPA2016D2 |
| 其它名稱： | 296-23616-6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
Register(N)
8-BitDatafor
Register(N+1)
SINGLE-AND MULTIPLE-BYTE TRANSFERS
SINGLE-BYTE WRITE
A6
A5
A4
A3
A2
A1
A0
R/W ACK A7
A6
A5
A4
A3
A2
A1
A0 ACK
D7
D6
D5
D4
D3
D2
D1
D0
ACK
Start
Condition
Stop
Condition
Acknowledge
I2CDeviceAddressand
Read/WriteBit
Register
DataByte
SLOS524D – JUNE 2008 – REVISED AUGUST 2009........................................................................................................................................................ www.ti.com
address and the read/write (R/W) bit to open communication with another device, and then waits for an
acknowledge condition. The TPA2016D2 holds SDA low during the acknowledge clock period to indicate
acknowledgment. When this acknowledgment occurs, the master transmits the next byte of the sequence. Each
device is addressed by a unique 7-bit slave address plus R/W bit (1 byte). All compatible devices share the same
signals via a bidirectional bus using a wired-AND connection.
An external pull-up resistor must be used for the SDA and SCL signals to set the logic high level for the bus.
When the bus level is 5 V, use pull-up resistors between 1 k
and 2 k.
Figure 36. Typical I2C Sequence
There is no limit on the number of bytes that can be transmitted between start and stop conditions. When the last
word transfers, the master generates a stop condition to release the bus. A generic data transfer sequence is
shown in Figure 36.
The serial control interface supports both single-byte and multi-byte read/write operations for all registers.
During multiple-byte read operations, the TPA2016D2 responds with data, one byte at a time, starting at the
register assigned, as long as the master device continues to respond with acknowledgments.
The TPA2016D2 supports sequential I2C addressing. For write transactions, if a register is issued followed by
data for that register and all the remaining registers that follow, a sequential I2C write transaction has occurred.
For I2C sequential write transactions, the register issued then serves as the starting point, and the amount of
data subsequently transmitted, before a stop or start is transmitted, determines the number of registers written.
As Figure 37 shows, a single-byte data write transfer begins with the master device transmitting a start condition
followed by the I2C device address and the read/write bit. The read/write bit determines the direction of the data
transfer. For a write data transfer, the read/write bit must be set to '0'. After receiving the correct I2C device
address and the read/write bit, the TPA2016D2 responds with an acknowledge bit. Next, the master transmits the
register byte corresponding to the TPA2016D2 internal memory address being accessed. After receiving the
register byte, the TPA2016D2 again responds with an acknowledge bit. Next, the master device transmits the
data byte to be written to the memory address being accessed. After receiving the register byte, the TPA2016D2
again responds with an acknowledge bit. Finally, the master device transmits a stop condition to complete the
single-byte data write transfer.
Figure 37. Single-Byte Write Transfer
20
Copyright 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): TPA2016D2
相關PDF資料 |
PDF描述 |
|---|---|
| TPA2035D1YZFT | IC AMP AUDIO PWR 2.75W D 9DSBGA |
| TPA3005D2PHPG4 | IC AMP AUDIO PWR 6W STER 48TQFP |
| TPA3007D1PWG4 | IC AMP AUDIO PWR 6.5W D 24TSSOP |
| TPA3100D2IRGZRQ1 | IC AMP AUDIO PWR 21.8W D 48QFN |
| TPA3123D2PWPR | IC AMP AUDIO PWR 25W D 24TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA2016DYZHT2 | 制造商:Texas Instruments 功能描述: |
| TPA2017D2 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:2.8-W/Ch Stereo Class-D Audio Amplifier with SmartGainTM Dynamic Range Compression and AGC |
| TPA2017D2RTJEVM | 功能描述:音頻 IC 開發工具 TPA2017D2 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| TPA2017D2RTJR | 功能描述:音頻放大器 2.8W/Ch Stereo Class-D Audio Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA2017D2RTJT | 功能描述:音頻放大器 2.8W/Ch Stereo Class-D Audio Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。