www.ti.com................................." />
參數資料
型號： TPA2016D2YZHT
廠商： Texas Instruments
文件頁數： 9/39頁
文件大小： 0K
描述： IC AMP AUDIO PWR 2.8W D 16DSBGA
標準包裝： 1
類型： D 類
輸出類型： 2 通道（立體聲）
在某負載時最大輸出功率 x 通道數量： 2.8W x 2 @ 4 歐姆
電源電壓： 2.5 V ~ 5.5 V
特點： 差分輸入，I²C，短路和熱保護，關機，音量控制
安裝類型： 表面貼裝
供應商設備封裝： 16-DSBGA（2x2）
封裝/外殼： 16-UFBGA，DSBGA
包裝： 標準包裝
產品目錄頁面： 876 (CN2011-ZH PDF)
配用： 296-31088-ND - EVAL MODULE FOR TPA2016D2
其它名稱： 296-23616-6
V
-dBV
O
U
T
V
-dBV
IN
MaxGain
= 22dB
MaxGain
= 30dB
1:1
www.ti.com........................................................................................................................................................ SLOS524D – JUNE 2008 – REVISED AUGUST 2009
Figure 33. Output Signal vs. Input Signal State Diagram Showing Different Maximum Gains
A particular application requiring maximum gain of 22dB, for example. Thus, set the maximum gain at 22dB. The
amplifier gain will never have a gain higher than 22dB; however, this will reduce the limiter range.
Attack, Release, and Hold time:
The attack time is the minimum time between gain decreases.
The release time is the minimum time between gain increases.
The hold time is the minimum time between a gain decrease (attack) and a gain increase (release). The hold
time can be deactivated. Hold time is only valid if greater than release time.
Successive gain decreases are never faster than the attack time. Successive gain increases are never faster
than the release time.
All time variables (attack, release and hold) start counting after each gain change performed by the AGC. The
AGC is allowed to decrease the gain (attack) only after the attack time finishes. The AGC is allowed to increase
the gain (release) only after the release time finishes counting. However, if the preceding gain change was an
attack (gain increase) and the hold time is enabled and longer than the release time, then the gain is only
increased after the hold time.
The hold time is only enabled after a gain decrease (attack). The hold time replaces the release time after a gain
decrease (attack). If the gain needs to be increased further, then the release time is used. The release time is
used instead of the hold time if the hold time is disabled.
The attack time should be at least 100 times shorter than the release and hold time. The hold time should be the
same or greater than the release time. It is important to select reasonable values for those variables in order to
prevent the gain from changing too often or too slow.
Figure 34 illustrates the relationship between the three time variables.
Copyright 2008–2009, Texas Instruments Incorporated
17
Product Folder Link(s): TPA2016D2
相關PDF資料
PDF描述
TPA2035D1YZFT IC AMP AUDIO PWR 2.75W D 9DSBGA
TPA3005D2PHPG4 IC AMP AUDIO PWR 6W STER 48TQFP
TPA3007D1PWG4 IC AMP AUDIO PWR 6.5W D 24TSSOP
TPA3100D2IRGZRQ1 IC AMP AUDIO PWR 21.8W D 48QFN
TPA3123D2PWPR IC AMP AUDIO PWR 25W D 24TSSOP
相關代理商/技術參數
參數描述
TPA2016DYZHT2 制造商:Texas Instruments 功能描述:
TPA2017D2 制造商:TI 制造商全稱:Texas Instruments 功能描述:2.8-W/Ch Stereo Class-D Audio Amplifier with SmartGainTM Dynamic Range Compression and AGC
TPA2017D2RTJEVM 功能描述:音頻 IC 開發工具 TPA2017D2 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
TPA2017D2RTJR 功能描述:音頻放大器 2.8W/Ch Stereo Class-D Audio Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA2017D2RTJT 功能描述:音頻放大器 2.8W/Ch Stereo Class-D Audio Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*