參數資料
型號： TPA3003D2PFB
廠商： TEXAS INSTRUMENTS INC
元件分類： 音頻控制
英文描述： 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQFP48
封裝： GREEN, PLASTIC, TQFP-48
文件頁數： 21/36頁
文件大小： 755K
代理商： TPA3003D2PFB
TPA3003D2
SLOS406A FEBRUARY 2003 REVISED MARCH 2003
28
www.ti.com
APPLICATION INFORMATION
differential input and BTL output
All of the class-D APAs and many class-AB APAs have differential inputs and bridge-tied load (BTL) outputs.
Differential inputs have two input pins per channel and amplify the difference in voltage between the pins.
Differential inputs reduce the common-mode noise and distortion of the input circuit. BTL is a term commonly
used in audio to describe differential outputs. BTL outputs have two output pins providing voltages that are 180
degrees out of phase. The load is connected between these pins. This has the added benefits of quadrupling
the output power to the load and eliminating a dc blocking capacitor.
A block diagram of the measurement circuit is shown in Figure 30. The differential input is a balanced input,
meaning the positive (+) and negative () pins will have the same impedance to ground. Similarly, the BTL output
equates to a balanced output.
C
IN
Audio Power
Amplifier
Generator
LowPass
RC Filter
C
IN
R
GEN
R
GEN
R
IN
R
IN
V
GEN
R
OUT
R
OUT
Analyzer
R
ANA
R
ANA
C
ANA
LowPass
RC Filter
R
L
C
ANA
TwistedPair Wire
Evaluation Module
TwistedPair Wire
Figure 30. Differential Input—BTL Output Measurement Circuit
The generator should have balanced outputs and the signal should be balanced for best results. An unbalanced
output can be used, but it may create a ground loop that will affect the measurement accuracy. The analyzer
must also have balanced inputs for the system to be fully balanced, thereby cancelling out any common mode
noise in the circuit and providing the most accurate measurement.
The following general rules should be followed when connecting to APAs with differential inputs and BTL
outputs:
D Use a balanced source to supply the input signal.
D Use an analyzer with balanced inputs.
D Use twisted-pair wire for all connections.
D Use shielding when the system environment is noisy.
D Ensure the cables from the power supply to the APA, and from the APA to the load, can handle the large
currents (see Table 2).
Table 2 shows the recommended wire size for the power supply and load cables of the APA system. The real
concern is the dc or ac power loss that occurs as the current flows through the cable. These recommendations
are based on 12-inch long wire with a 20-kHz sine-wave signal at 25
°C.
相關PDF資料
PDF描述
TPA3003D2PFBRG4 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQFP48
TPA3003D2PFBG4 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQFP48
TPA3004D2PHPRG4 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQFP48
TPA3004D2PHPG4 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PQFP48
TPA3005D2PHPR 6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48
相關代理商/技術參數
參數描述
TPA3003D2PFBG4 功能描述:音頻放大器 Ster Lo-Pwr Wide Sply Vltg Class-D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA3003D2PFBR 功能描述:音頻放大器 Ster Lo-Pwr Wide Sply Vltg Class-D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA3003D2PFBRG4 功能描述:音頻放大器 Ster Lo-Pwr Wide Sply Vltg Class-D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA3004 制造商:TI 制造商全稱:Texas Instruments 功能描述:12-W STEREO CLASS-D AUDIO POWER AMPLIFIER WITH DC VOLUME CONTROL
TPA3004D2 制造商:TI 制造商全稱:Texas Instruments 功能描述:12-W STEREO CLASS-D AUDIO POWER AMPLIFIER WITH DC VOLUME CONTROL
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*