- 您現在的位置：買賣IC網 > PDF目錄383962 > TPS2393DBTRG4 (Texas Instruments, Inc.) FULL-FEATURED-48-V HOTSWAP POWER MANAGER PDF資料下載
參數資料
| 型號： | TPS2393DBTRG4 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | FULL-FEATURED-48-V HOTSWAP POWER MANAGER |
| 中文描述： | 全功能- 48 - V熱切換電源管理器 |
| 文件頁數： | 7/34頁 |
| 文件大小： | 567K |
| 代理商： | TPS2393DBTRG4 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
SLUS536C AUGUST 2002 REVISED AUGUST 2004
www.ti.com
7
PIN ASSIGNMENTS
ISENS
: Current sense input. An external low-value resistor connected between this pin and VIN is used to feed
back current magnitude information to the TPS2392 and TPS2393. There are two internal device thresholds
associated with the voltage at the ISENS pin. During ramp-up of the load’s input capacitance, or during other periods
of excessive demand, the HSPM acts to limit this voltage to 40 mV. Whenever the LCA is in current regulation mode,
the capacitor at FLTTIME is charged to activate the timer. If, when the LCA is driving to its supply rail, a fast-acting
fault such as a short-circuit, causes the ISENS voltage to exceed 100 mV (the overload threshold), the GATE pin
is pulled low rapidly, bypassing the fault timer.
OVLO
: Voltage sense input for supply overvoltage lockout (OVLO) protection. Overvoltage protection can be
achieved by applying a divided down sample of the input supply voltage to this pin. In order to turn on gate drive to
the external FET, the OVLO pin must be below the 1.4-V typical threshold, while all other input qualifications are met.
If the OVLO pin is raised above this threshold, as with increasing supply voltage, the GATE output is pulled low,
interrupting the supply to the load. An internal 10-
μ
A pull-up is switched to this pin when the threshold is exceeded,
providing a mechanism for setting the amount of OVLO hysteresis along with the trip threshold.
PG
: Open-drain, active-low indication of load power good condition. The TPS2392 and TPS2393 devices define
power good as the voltage at the DRAINSNS pin below the power good threshold, and the voltage at the IRAMP pin
being above 5 V. This assures that full programmed sourcing current is available to the load prior to declaring power
good, even with very slow current ramp rates. The additional protection prevents potential discharging of the module
bulk capacitance during load turn-on.
RTN
: Positive supply input for the TPS2392 and TPS2393. For negative voltage systems, the supply pin connects
directly to the return node of the input power bus. Internal regulators step down the input voltage to generate the
various supply levels used by the TPS2392 and TPS2393.
UVLO
: Voltage sense input for supply uvervoltage lockout (UVLO) protection. Undervoltage protection can be
achieved by applying a divided down sample of the input supply voltage to this pin. In order to turn on the gate drive
to the external FET, the UVLO pin must be above the 1.4-V typical threshold, while all other input qualifications are
met. If the UVLO pin drops below this threshold, as with decreasing supply voltage, the GATE output is pulled low,
interrupting the supply to the load. An internal 10-
μ
A pullup is switched to this pin when the threshold is exceeded,
providing a mechanism for setting the amount of UVLO hysteresis along with the trip threshold.
For proper operation, a minimum 1500-pF capacitor, connected between the UVLO and VIN pins, is required.
VIN
: Negative supply input and reference pin for the TPS2392 and TPS2393. This pin connects directly to the input
supply negative rail. The input and output pins and all internal circuitry are referenced to this pin, so it is essentially
the GND or VSS pin of the device.
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2491EVM-002 | +48V Hot Swap Power Manager Evaluation Kit(在+48V熱插拔電源管理中應用的評估) |
| TPS2490EVM-001 | +48V Hot Swap Power Manager Evaluation Kit(在+48V熱插拔電源管理中應用的評估) |
| TPS3106K33DBV | UltraLow Supply-Current/Supply-Voltage Supervisory Circuits |
| TPS3600D50PWRG4 | BATTERY-BACKUP SUPERVISORS FOR LOW-POWER PROCESSORS |
| TPS3600x20PW | BATTERY-BACKUP SUPERVISORS FOR LOW-POWER PROCESSORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS2393EVM | 功能描述:電源管理IC開發工具 Simple -48V Hot Swap Contr EVM RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS2393PW | 功能描述:熱插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2393PWG4 | 功能描述:熱插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2393PWR | 功能描述:熱插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2393PWRG4 | 功能描述:熱插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。