- 您現在的位置：買賣IC網 > PDF目錄98280 > TPS2421-2DDAR (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 PDF資料下載
參數資料
| 型號： | TPS2421-2DDAR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封裝： | PLATSIC, SOP-8 |
| 文件頁數： | 22/24頁 |
| 文件大?。?/td> | 1297K |
| 代理商： | TPS2421-2DDAR |
0 04
OUT
IN
OUT
V
.
I
=
-
www.ti.com
SLUS907D – JANUARY 2009 – REVISED AUGUST 2010
EN: When this pin is pulled low, the device is enabled. The input threshold is hysteretic, allowing the user to
program a startup delay with an external RC circuit. EN is pulled to VIN by a 10-M resistor, pulled to GND by
16.8 M
and is clamped to ground by a 7-V Zener diode. Because high impedance pullup/down resistors are
used to reduce current draw, any external FET controlling this pin should be low leakage.
If EN is tied to GND at startup and VIN does not ramp quickly the TPS2421 may momentarily turn off then on
during startup. This can happen if a capacitive load momentarily pulls down the input voltage below the UV
threshold. If necessary, this can be avoided by delaying EN assertion until VIN is fully up.
VIN: Input voltage to the TPS2421. The recommended operating voltage range is 3 V to 20 V. All VIN pins should
be connected together and to the power source.
VOUT: Output connection for the TPS2421. When switched on the output voltage will be approximately:
(4)
All VOUT pins should be connected together and to the load.
PG: Active low, Open Drain output, Power Good indicates that there is no fault condition and the output voltage
is within 0.5 V of the input voltage. PG becomes operational before UV, whenever VIN is greater than 1 V.
Copyright 2009–2010, Texas Instruments Incorporated
7
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2459RHBR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC32 |
| TPS2459RHB | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC32 |
| TPS24701DGK | POWER SUPPLY SUPPORT CKT, PDSO8 |
| TPS24710DGS | POWER SUPPLY SUPPORT CKT, PDSO10 |
| TPS24710 | POWER SUPPLY SUPPORT CKT, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS2421-2EVM-03 | 功能描述:電源管理IC開發工具 TPS2421-2 Hot Swap Controller Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS2456ARHHR | 制造商:Texas Instruments 功能描述:IC HOT SWAP/ORING CTRLR 36VQFN 制造商:Texas Instruments 功能描述:Dual Hot Swap ORing Controller 制造商:Texas Instruments 功能描述:CONTROLLER |
| TPS2456ARHHT | 功能描述:熱插拔功率分布 Dual 12V Prot and Blocking ORing Cntrl RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2456EVM | 功能描述:電源管理IC開發工具 TPS2456 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS2456RHHR | 功能描述:熱插拔功率分布 Dual 12V Pro & Block ing ORing Cntrlr RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。