- 您現在的位置：買賣IC網 > PDF目錄98282 > TPS53851RHHT (TEXAS INSTRUMENTS INC) SWITCHING CONTROLLER, PQCC36 PDF資料下載
參數資料
| 型號： | TPS53851RHHT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, PQCC36 |
| 封裝： | PLASTIC, VQFN-36 |
| 文件頁數： | 13/66頁 |
| 文件大?。?/td> | 1264K |
| 代理商： | TPS53851RHHT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
R
BIAS + 0.7
R1
V
OUT * 0.7
SLUS985 – DECEMBER 2009
www.ti.com
(4)
5.10 PROGRAMMABLE INPUT UNDERVOLTAGE LOCK OUT PROTECTION
A voltage divider that sets 2 V on the UVLO_CEx pins determines when the controller begins to operate.
The internal regulators are enabled when the voltage on the UVLO_CEx pins exceeds 1 V, but switching
commences when the voltage is 2 V.
5.11 POWER ON RESET (POR)
The internal POR function ensures the VREG and BP5 voltages are within their regulation windows before
the controller is allowed to start.
5.12 OVERCURRENT
The operation during an overcurrent condition is described in the ‘Overcurrent Detection and Hiccup
Mode’ section. In summary, when the controller detects 7 clock cycles of an overcurrent condition, the
upper and lower MOSFETs are turned off and the controller enters a 'hiccup' mode'. After seven soft start
cycles, normal switching is attempted. If the overcurrent has cleared, normal operation resumes, otherwise
the sequence repeats.
5.13 OUTPUT UNDERVOLTAGE PROTECTION
If the output voltage, as sensed by U23 of the Functional Block Diagram on the FB pin becomes less than
0.588 V, the undervoltage protection threshold (84% of VREF), the controller enters the hiccup mode as
described in the Overcurrent Detection and Hiccup Mode section.
5.14 OUTPUT OVERVOLTAGE PROTECTION
Output overvoltage is defined as any voltage greater than the regulation level that appears on the output.
Overvoltage protection is accomplished by the feedback loop monitoring the output voltage via the FB pin.
If, during operation the output voltage experiences an overvoltage condition the FB pin voltage rises and
the control loop turns the upper FET off and the lower FET is turned on until the output returns to set level.
This puts the overvoltage channel in a boost mode configuration and tends to cause the input voltage to
be boosted up.
If the output overvoltage condition exists prior to the controller PWM switching starting, i.e., no switching
has commenced, the overvoltaged channel does not start PWM switching. This controller allows for
operating with a pre-biased output. Since the output is greater than the regulation voltage, no PWM
switching occurs.
DESIGN HINT: Care must be taken to insure there is sufficient load on the input voltage to prevent
excessive boosting.
5.15 CLKFLT, CLKIO PIN FAULT
If the CLKIO signal is to be distributed from the master to the slave controllers, and is not there, the slave
controller enters a ‘Standby’ mode. The upper and lower MOSFETs are turned off but the internal 5-V
regulator is still active and VREG is present. The CLKIO signal could be turned off at the master controller
or the connection to the slave CLKIO input could be opened. If the CLKIO signal is restored, normal
operation continues.
20
APPLICATION INFORMATION
Copyright 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS53851
相關PDF資料 |
PDF描述 |
|---|---|
| TPS54010PWPG4 | 25 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28 |
| TPS54040DGQ | 0.5 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS54073PWPRG4 | 25 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28 |
| TPS54073PWPR | 25 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28 |
| TPS54073PWP | 25 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS53915EVM-587 | 功能描述:TPS53915 SWIFT?, D-CAP3?, Eco-Mode? DC/DC, Step Down 1, Non-Isolated Outputs Evaluation Board 制造商:texas instruments 系列:SWIFT?，D-CAP3?，Eco-Mode? 零件狀態:有效 主要用途:DC/DC，步降 輸出和類型:1，非隔離 功率 - 輸出:- 電壓 - 輸出:1.2V 電流 - 輸出:12A 電壓 - 輸入:12V 穩壓器拓?fù)?降壓 頻率 - 開關:- 板類型:完全填充 所含物品:板 使用的 IC/零件:TPS53915 標準包裝:1 |
| TPS53915RVET | 制造商:Texas Instruments 功能描述:1.5V TO 18V INPUT (4.5V TO 25V BIAS), 12-A SYNCHRONOUS STEP- - Tape and Reel 制造商:Texas Instruments 功能描述:IC REG BUCK SYNC ADJ 12A 28VQFN |
| TPS5401 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:0.5-A, 42-V Input, Step-Down SWIFT? Converter |
| TPS54010 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:SWIFT Converter Product Portfolio |
| TPS54010EVM-067 | 功能描述:電源管理IC開發工具 4.0 Vin DC/DC Conv RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。