- 您現在的位置：買賣IC網 > PDF目錄98282 > TPS54260QDGQRQ1 (TEXAS INSTRUMENTS INC) 2.5 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 PDF資料下載
參數資料
| 型號： | TPS54260QDGQRQ1 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 2.5 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封裝： | GREEN, PLASTIC, MSOP-10 |
| 文件頁數： | 6/48頁 |
| 文件大小： | 1456K |
| 代理商： | TPS54260QDGQRQ1 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
4.6
4.8
5
5.2
5.4
5.6
0
0.05
0.10
0.15
0.20
I -OutputCurrent- A
O
V
-InputV
oltage-V
I
V =5V
O
Start
Stop
3
3.2
3.4
3.6
3.8
4
0
0.05
0.10
0.15
0.20
I -OutputCurrent- A
O
V
-InputV
oltage-V
I
V =3.3V
O
Start
Stop
SLVSAH8A
– DECEMBER 2010 – REVISED APRIL 2011
DETAILED DESCRIPTION (continued)
Attention must be taken in maximum duty cycle applications which experience extended time periods with light
loads or no load. When the voltage across the BOOT capacitor falls below the 2.1V UVLO threshold, the high
side MOSFET is turned off, but there may not be enough inductor current to pull the PH pin down to recharge the
BOOT capacitor. The high side MOSFET of the regulator stops switching because the voltage across the BOOT
capacitor is less than 2.1V. The output capacitor then decays until the difference in the input voltage and output
voltage is greater than 2.1V, at which point the BOOT UVLO threshold is exceeded, and the device starts
switching again until the desired output voltage is reached. This operating condition persists until the input
voltage and/or the load current increases. It is recommended to adjust the VIN stop voltage greater than the
BOOT UVLO trigger condition at the minimum load of the application using the adjustable VIN UVLO feature with
resistors on the EN pin.
The start and stop voltages for typical 3.3V and 5V output applications are shown in Figure 25 and Figure 26.
The voltages are plotted versus load current. The start voltage is defined as the input voltage needed to regulate
the output within 1%. The stop voltage is defined as the input voltage at which the output drops by 5% or stops
switching.
During high duty cycle conditions, the inductor current ripple increases while the BOOT capacitor is being
recharged resulting in an increase in ripple voltage on the output. This is due to the recharge time of the boot
capacitor being longer than the typical high side off time when switching occurs every cycle.
Figure 25. 3.3V Start/Stop Voltage
Figure 26. 5.0V Start/Stop Voltage
Error Amplifier
The TPS54260-Q1 has a transconductance amplifier for the error amplifier. The error amplifier compares the
VSENSE voltage to the lower of the SS/TR pin voltage or the internal 0.8V voltage reference. The
transconductance (gm) of the error amplifier is 310
μA/V during normal operation. During the slow start operation,
the transconductance is a fraction of the normal operating gm. When the voltage of the VSENSE pin is below
0.8V and the device is regulating using the SS/TR voltage, the gm is 70
μA/V.
The frequency compensation components (capacitor, series resistor and capacitor) are added to the COMP pin
to ground.
Voltage Reference
The voltage reference system produces a precise
±2% voltage reference over temperature by scaling the output
of a temperature stable bandgap circuit.
Adjusting the Output Voltage
The output voltage is set with a resistor divider from the output node to the VSENSE pin. It is recommended to
use 1% tolerance or better divider resistors. Start with a 10 k
for the R2 resistor and use the Equation 1 to
calculate R1. To improve efficiency at light loads consider using larger value resistors. If the values are too high
the regulator will be more susceptible to noise and voltage errors from the VSENSE input current will be
noticeable.
14
Copyright
2010–2011, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| TPS5430MDDAREPG4 | 8.5 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO8 |
| TPS54310MPWPREP | 6 A SWITCHING REGULATOR, 775 kHz SWITCHING FREQ-MAX, PDSO20 |
| TPS54310PWPRG4 | 6 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO20 |
| TPS54320RHLR | SWITCHING REGULATOR, 1320 kHz SWITCHING FREQ-MAX, PQCC14 |
| TPS54320RHL | SWITCHING REGULATOR, PQCC14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS54260QDRCRQ1 | 功能描述:Buck Switching Regulator IC Positive Adjustable 0.8V 1 Output 2.5A 10-VFDFN Exposed Pad 制造商:texas instruments 系列:汽車級，AEC-Q100，Eco-Mode? 包裝:剪切帶（CT） 零件狀態:有效 功能:降壓 輸出配置:正 拓?fù)?降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:3.5V 電壓 - 輸入（最大值）:60V 電壓 - 輸出（最小值/固定）:0.8V 電壓 - 輸出（最大值）:60V 電流 - 輸出:2.5A 頻率 - 開關:100kHz ~ 2.5MHz 同步整流器:無 工作溫度:-40°C ~ 125°C（TA） 安裝類型:表面貼裝 封裝/外殼:10-VFDFN 裸露焊盤 供應商器件封裝:10-VSON（3x3） 標準包裝:1 |
| TPS54260QDRCTQ1 | 功能描述:Buck Switching Regulator IC Positive Adjustable 0.8V 1 Output 2.5A 10-VFDFN Exposed Pad 制造商:texas instruments 系列:汽車級，AEC-Q100，Eco-Mode? 包裝:剪切帶（CT） 零件狀態:有效 功能:降壓 輸出配置:正 拓?fù)?降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:3.5V 電壓 - 輸入（最大值）:60V 電壓 - 輸出（最小值/固定）:0.8V 電壓 - 輸出（最大值）:60V 電流 - 輸出:2.5A 頻率 - 開關:100kHz ~ 2.5MHz 同步整流器:無 工作溫度:-40°C ~ 125°C（TA） 安裝類型:表面貼裝 封裝/外殼:10-VFDFN 裸露焊盤 供應商器件封裝:10-VSON（3x3） 標準包裝:1 |
| TPS54262EVM | 功能描述:電源管理IC開發工具 TPS54262EVM Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS54262QPWPRQ1 | 功能描述:DC/DC 開關控制器 Auto Cat 2A 60V step down DC/DC converter RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS54283 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:SWIFT Converter Product Portfolio |
發布緊急采購，3分鐘左右您將得到回復。