參數資料
型號： TS4956EIKJT
廠商： STMICROELECTRONICS
元件分類： 音頻／視頻放大
英文描述： 1.055 W, 2 CHANNEL, AUDIO AMPLIFIER, PBGA18
封裝： ROHS COMPLIANT, FCP-18
文件頁數： 45/52頁
文件大小： 1709K
代理商： TS4956EIKJT
TS4956
Typical application schematic
5/51
2.1
I2C interface
The TS4956 uses a serial bus, which conforms to the IC protocol (the TS4956 must be
powered when it is connected to IC bus), to control the chip’s functions via two wires: Clock
and Data.
The Clock line and the Data line are bidirectional (open-collector) with an external chip pull-
up resistor (typically 10 k
). The maximum clock frequency in fast-mode specified by the IC
standard is 400kHz, and this frequency is supported by the TS4956. In this application, the
TS4956 is always the slave device and the controlling MCU is the master device.
The I2CVCC pin determines the power supply of the TS4956’s I2C interface. The voltage
connected to this pin must be equal or less than the TS4956 power supply voltage VCC. The
minimum value of the I2CVCC voltage is 2.7V.
When the I2CVCC pin is connected to an I2C voltage, the TS4956 is ready to communicate
via the I2C bus.
When the I2CVCC pin is connected to the ground, the TS4956 is in total standby mode, with
an ultra low standby current on the order of a few nanoamperes. In this condition the
TS4956 cannot receive I2C command from the I2C bus.
In both cases, pins SDA and SCL must respect logic HI or logic LOW thresholds (not
floating) presented in
Table 3 on page 2, in order for the circuit to function properly.
Table on page 5 summarizes the pin descriptions for the IC bus interface.
2.1.1
IC operation description
The host MCU can write into the TS4946 control register to control the TS4956 and read
from the control register to get the current configuration of the TS4956. The TS4956 is
addressed by a single byte consisting of a 7-bit slave address and an R/W bit. The TS4956
control register address is $5Dh.
Table 6.
The first byte after the START message for addressing the device
In order to write data into the TS4956 control register, after the “start” message the MCU
must send the following data:
●
send byte with the IC 7-bit slave address and with the R/W bit set low
●
send the data (control register setting)
All bytes are sent with MSB bit first. The transfer of written data ends with a “stop” message.
When transmitting several data, the data can be written with no need to repeat the “start”
message and addressing byte with the slave address.
Table 5.
IC bus interface: pin descriptions
Pin
Functional description
SDA
This is the serial data pin
SCL
This is the clock input pin
I2CVCC
I2C interface power supply
A6
A5
A4
A3
A2
A1
A0
Rw
101
1
0
1
X
相關PDF資料
PDF描述
TS4956EKIJT 1.06 W, 2 CHANNEL, AUDIO AMPLIFIER, PBGA18
TS4961TIQT 1.5 W, 1 CHANNEL, AUDIO AMPLIFIER, QCC16
TS4962EIJT 3 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9
TS4962EIKJT 3 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9
TS4962EKIJT 3 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9
相關代理商/技術參數
參數描述
TS4961TIQT 功能描述:音頻放大器 MONO CLASS D AUDIO PWR AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TS4962 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2.8W filter-free mono class D audio power amplifier
TS4962_07 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2.8W filter-free mono class D audio power amplifier
TS4962_10 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2.8 W filter-free mono class D audio power amplifier
TS4962EIJT 制造商:STMicroelectronics 功能描述:AUD AMP SPKR 1CH MONO 2W CLS-D 9PIN FLIP-CHIP - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*