- 您現(xiàn)在的位置：買賣IC網 > PDF目錄11806 > TXS02326RGER (Texas Instruments)IC SIM CARD MUX 2:1 24VQFN PDF資料下載
參數資料
| 型號： | TXS02326RGER |
| 廠商： | Texas Instruments |
| 文件頁數： | 35/35頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SIM CARD MUX 2:1 24VQFN |
| 產品培訓模塊： | Voltage Level Translation |
| 標準包裝： | 1 |
| 應用： | 移動電話 |
| 接口： | I²C |
| 電源電壓： | 1.7 V ~ 3.3 V |
| 封裝/外殼： | 24-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 24-VQFN 裸露焊盤（4x4） |
| 包裝： | 標準包裝 |
| 安裝類型： | 表面貼裝 |
| 其它名稱： | 296-27948-6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁
Slave Address
0
1
0
IRQ
R/W
SCES795C
– SEPTEMBER 2010 – REVISED FEBRUARY 2011
BASIC DEVICE OPERATION
The TXS02326 is controlled through a standard I2C interface reference to VDDIO. It is connected between the
two SIM card slots and the SIM/UICC interface of the baseband. The device uses VBAT and VDDI/O as supply
voltages. The supply voltage for each SIM card is generated by an on-chip low drop out regulator. The interface
between the baseband and the TXS02326 is reference to VDDIO while the interface between the TXS02326 and
the SIM card is referenced to the LDO output of either VSIM1 or VSIM2 depending on which slot is being
selected. The VDDIO on the baseband side normally does not exceed 1.8V, thus voltage level shifting is needed
to support a 3V SIM/UICC interface (Class B).
The TXS02326 has two basic states, the reset and operation state. The baseband utilizes information in the
status registers to determine how to manipulate the control registers to properly switch between two SIM cards.
These fundamental sequences are outlined below and are to help the user to successfully incorporate this device
into the system.
DEVICE ADDRESS
The address of the device is shown below:
Address Reference
IRQ@ Reset
R/W
Slave Address
0
0 (W)
120 (decimal), 78(h)
0
1 (R)
121 (decimal), 79(h)
1
0 (W)
122 (decimal), 7A(h)
1
1 (R)
123 (decimal), 7B(h)
RESET STATE
In the reset state the device settings are brought back to their default values and any SIM card that has been
active is deactivated. After reset, neither of the UICC/SIM interfaces is selected. The active pull-downs at the
UICC/SIM interface are automatically activated. To ensure the system powers up in an operational state, device
uses an internal 32 KHz clock for internal timing generation. After power up, the system has the option to
continue to utilize the internal clock or select an external clock source. This clock source is selectable by the
Clock Source Select I2C register bit.
Power up the TXS02326 by asserting VBAT to enter the operation state
I2C Interface becomes active with the VDD_I/O supply
RESET summary:
Any pending interrupts are cleared
I2C registers are in the default state
BSI and SDN counter value in the registers are set to four clock cycles or
“0000 0100”
Both on chip regulators are set to 1.8V and disabled
All SIM1 and SIM2 signals are pulled to GND
2010–2011, Texas Instruments Incorporated
9
Product Folder Link(s): TXS02326
相關PDF資料 |
PDF描述 |
|---|---|
| MS3114E12-8PW | CONN RCPT 8POS JAM NUT W/PINS |
| MS3114E12-8P | CONN RCPT 8POS JAM NUT W/PINS |
| MS3100A32-1P | CONN RCPT 5POS WALL MNT W/PINS |
| MS27497E12A4P | CONN RCPT 4POS WALL MNT W/PINS |
| D38999/20MB98PB | CONN RCPT 6POS WALL MNT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TXS02612 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:SDIO PORT EXANDER WITH VOLTAGE-LEVEL TRANSLATION |
| TXS02612_10 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:SDIO PORT EXANDER WITH VOLTAGE-LEVEL TRANSLATION |
| TXS02612RTWR | 功能描述:轉換 - 電壓電平 SDIO Port Expander RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
| TXS02612ZQSR | 功能描述:接口 - 專用 SDIO Port Expander RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| TXS02AB00-04AI | 制造商:TE Connectivity 功能描述:TXS02AB00-04AI |
發(fā)布緊急采購，3分鐘左右您將得到回復。