- 您現在的位置：買賣IC網 > PDF目錄379479 > UCC2813-0QDRQ1 (Texas Instruments, Inc.) LOW-POWER BICMOS CURRENT-MODE PWM PDF資料下載
參數資料
| 型號： | UCC2813-0QDRQ1 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | LOW-POWER BICMOS CURRENT-MODE PWM |
| 中文描述： | 低功率BiCMOS電流模式PWM |
| 文件頁數： | 6/13頁 |
| 文件大?。?/td> | 404K |
| 代理商： | UCC2813-0QDRQ1 |
SGLS245 MAY 2004
6
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
detailed terminal descriptions
COMP
COMP is the output of the error amplifier and the input of the PWM comparator.
Unlike other devices, the error amplifier in the UCC2813 family is a true, low output-impedance, 2-MHz
operational amplifier. As such, the COMP terminal can both source and sink current. However, the error
amplifier is internally current limited, so that one can command zero duty cycle by externally forcing COMP to
GND.
The UCC2813 family features built-in full cycle soft start. Soft start is implemented as a clamp on the maximum
COMP voltage.
CS
CS is the input to the current sense comparators. The UCC2813 family has two different current sense
comparators: the PWM comparator and an overcurrent comparator.
The UCC2813 family contains digital current sense filtering, which disconnects the CS terminal from the current
sense comparator during the 100 ns interval immediately following the rising edge of the OUT pin. This digital
filtering, also called leading-edge blanking, means that in most applications, no analog filtering (RC filter) is
required on CS. Compared to an external RC filter technique, the leading-edge blanking provides a smaller
effective CS to OUT propagation delay. Note, however, that the minimum non-zero on-time of the OUT signal
is directly affected by the leading-edge-blanking and the CS to OUT propagation delay.
The overcurrent comparator is only intended for fault sensing, and exceeding the overcurrent threshold causes
a soft start cycle.
FB
FB is the inverting input of the error amplifier. For best stability, keep FB lead length as short as possible and
FB stray capacitance as small as possible.
ground (GND)
GND is reference ground and power ground for all functions on this part.
OUT
OUT is the output of a high-current power driver capable of driving the gate of a power MOSFET with peak
currents exceeding
750 mA. OUT is actively held low when V
CC
is below the UVLO threshold.
The high-current power driver consists of FET output devices, which can switch all of the way to GND and all
of the way to V
CC
. The output stage also provides a low impedance to overshoot and undershoot. This means
that in many cases external Schottky clamp diodes are not required.
相關PDF資料 |
PDF描述 |
|---|---|
| UCC2813PWTR-2 | Low Power Economy BiCMOS Current Mode PWM |
| UCC2813NTR-0 | Low Power Economy BiCMOS Current Mode PWM |
| UCC2813NTR-1 | Low Power Economy BiCMOS Current Mode PWM |
| UCC2813-2QDRQ1 | LOW-POWER BICMOS CURRENT-MODE PWM |
| UCC2813NTR-2 | Low Power Economy BiCMOS Current Mode PWM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UCC2813-1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low Power Economy BiCMOS Current Mode PWM |
| UCC2813-1QDRQ1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:LOW-POWER BICMOS CURRENT-MODE PWM |
| UCC2813-2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low Power Economy BiCMOS Current Mode PWM |
| UCC2813-2QDRQ1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:LOW-POWER BICMOS CURRENT-MODE PWM |
| UCC2813-3 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low Power Economy BiCMOS Current Mode PWM |
發布緊急采購，3分鐘左右您將得到回復。