- 您現在的位置：買賣IC網 > PDF目錄379501 > UPD72001G-11-22 (NEC Corp.) MULTI-PROTOCOL SERIAL CONTROLLERS PDF資料下載
參數資料
| 型號： | UPD72001G-11-22 |
| 廠商： | NEC Corp. |
| 英文描述： | MULTI-PROTOCOL SERIAL CONTROLLERS |
| 中文描述： | 多協議串行控制器 |
| 文件頁數： | 10/40頁 |
| 文件大?。?/td> | 206K |
| 代理商： | UPD72001G-11-22 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
μ
PD72001-11, 72001-A8
10
(b) Non-vector mode (CR2A: D7 = “0”)
In this mode, the PRI pin controls only the generation of interrupts because the INTAK sequence is not used.
If an interrupt vector output mode other than Type A-3 and Type B-2 is selected, generation of an interrupt
signal is enabled if “L” is input to the PRI pin. The interrupt signal is not generated if “H” is input to PRI.
If an interrupt daisy chain is configured, inputting “L” to this pin indicates that a device having a higher priority
does not acknowledge interrupt processing or does not have an interrupt request, and only the MPSC with
“L” input to its PRI pin can generate an interrupt.
(13)PRO (Priority Output) ... Output
This pin is used when an interrupt daisy chain is configured. This output pin is active-low, and controls generation
of interrupts requests from a device with a lower priority. Usually, this pin is used along with the PRI pin, and
its operation is as follows:
When PRI = “H”, PRO = “H”
When PRI = “L”, PRO goes “H” if there is an interrupt request, and goes “L” if there is no interrupt request.
(14)DRQT
X
A (DMA Request T
X
A) ... Output
This pin outputs a DMA request to a DMA controller. This pin is active-high. It goes “H” if the transmitter of channel
A has entered the T
X
Buffer Empty status. The condition under which this pin goes “H” differs as follows depending
on the setting of the CR1 and D2 bits.
CR1: D2 = “0”: The DRQT
X
A pin goes “H” when the transmitter has entered the T
X
Buffer Empty status after
the first transmit data has been written. It does not go “H” when the transmitter has entered
the T
X
Buffer Empty status after reset.
CR1: D2 = “1”: The DRQT
X
A pin goes “H” when the transmitter has entered the T
X
Buffer Empty status.
This signal is reset when transmit data has been written to channel A.
(15)DRQR
X
A (DMA Request R
X
A) ... Output
This pin outputs a DMA request to a DMA controller. This pin is active-high and goes “H” if the receiver of channel
A has entered the R
X
Character Available status. This signal is reset only when receive data has been read from
channel A.
(16)DTRA/DRQT
X
B (Data Terminal Ready A/DMA Request T
X
B) ... Output
The function of this pin is changed as follows depending on the setting of CR2A: D1 and D0.
(a) When CR2A: D1, D0 = “0, 0” or “0, 1”
This pin functions as the DTRA pin. This pin is a general-purpose output pin and can be used to control a
modem, etc. The operation of the DTRA pin is as follows:
When CR5A: D7 = “0”, DTRA = “H”
When CR5A: D7 = “1”, DTRA = “L”
(b) When CR2A: D1, D0 = “1, 0”
This pin functions as the DRQT
X
B output pin. The function of this pin is the same as the DRQT
X
A pin, except
this pin is used with channel B.
(17)DTRB/DRQR
X
B (Data Terminal Ready B/DMA Request R
X
B) ... Output
The function of this pin changes as follows depending on the setting of CR2A: D1 and D0.
相關PDF資料 |
PDF描述 |
|---|---|
| UPD72001C-11 | MULTI-PROTOCOL SERIAL CONTROLLERS |
| UPD72001L-11 | 5015 RR 14#16 SKT RECP |
| UPD72001G-A8-22 | MULTI-PROTOCOL SERIAL CONTROLLERS |
| UPD720101GJ-UEN | USB2.0 HOST CONTROLLER |
| UPD720101 | USB2.0 HOST CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UPD720101F1 | 制造商:NEC Electronics Corporation 功能描述: |
| UPD720101F1-EA8 | 制造商:NEC Electronics Corporation 功能描述: |
| UPD720101F1-EA8 ( PRICE BREAK 250K - | 制造商:Renesas Electronics Corporation 功能描述: |
| UPD720101F1-EA8_NEC | 制造商:Renesas Electronics Corporation 功能描述: |
| UPD720101F1-EA8-A | 功能描述:HOST CTLR USB 2.0 144-FBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
發布緊急采購，3分鐘左右您將得到回復。