- 您現在的位置：買賣IC網 > PDF目錄359314 > V23832-T2431-M101 (INFINEON TECHNOLOGIES AG) PAROLI 2 Tx AC, 1.25 Gbit/s PDF資料下載
參數資料
| 型號： | V23832-T2431-M101 |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 英文描述： | PAROLI 2 Tx AC, 1.25 Gbit/s |
| 中文描述： | 帕羅利2個發送，1.25千兆交流/秒 |
| 文件頁數： | 11/33頁 |
| 文件大小： | 709K |
| 代理商： | V23832-T2431-M101 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
V23832-T2531-M101
V23832-R511-M101
Description
Data Sheet
11
2003-11-19
When Gigabit switching components are found on a PCB (e.g. multiplexer, serializer-
deserializer, clock data recovery, etc.), any opening of the chassis may leak radiation;
this may also occur at chassis slots other than that of the device itself. Thus every
mechanical opening or aperture should be as small as feasible and its length carefully
considered.
On the board itself, every data connection should be an impedance matched line (e.g.
micro strip, strip line or coplanar strip line). Data (D) and Data-not (Dn) should be routed
symmetrically. Vias should be avoided. Where internal termination inside an IC or a
PAROLI module is not present, a line terminating resistor must be provided.
The decision of how best to establish a ground depends on many boundary conditions.
This decision may turn out to be critical for achieving lowest EMI performance. At RF
frequencies the ground plane will always carry some amount of RF noise. Thus the
ground and
V
CC
planes are often major radiators inside an enclosure.
As a general rule, for small systems such as PCI cards placed inside poorly shielded
enclosures, the common ground scheme has often proven to be most effective in
reducing RF emissions. In a common ground scheme, the PCI card becomes more
equipotential with the chassis ground. As a result, the overall radiation will decrease. In
a common ground scheme, it is strongly recommended to provide a proper contact
between signal ground and chassis ground at every location where possible. This
concept is designed to avoid hotspots which are places of highest radiation, caused
when only a few connections between chassis and signal grounds exist. Compensation
currents would concentrate at these connections, causing radiation.
However, as signal ground may be the main cause for parasitic radiation, connecting
chassis ground and signal ground at the wrong place may result in enhanced RF
emissions. For example, connecting chassis ground and signal ground at a front panel/
bezel/chassis by means of a fiber optic module may result in a large amount of radiation
especially where combined with an inadequate number of grounding points between
signal ground and chassis ground. Thus the fiber optic module becomes a single contact
point increasing radiation emissions. Even a capacitive coupling between signal ground
and chassis ground may be harmful if it is too close to an opening or an aperture. For a
number of systems, enforcing a strict separation of signal ground from chassis ground
may be advantageous, providing the housing does not present any slots or other
discontinuities. This separate ground concept seems to be more suitable in huge
systems.
The return path of RF current must also be considered. Thus a split ground plane
between Tx and Rx paths may result in severe EMI problems.
The bezel opening for a transceiver should be sized so that all contact springs of the
transceiver cage make good electrical contact with the face plate.
Please consider that the PCB may behave like a dielectric waveguide. With a dielectric
constant of 4, the wavelength of the harmonics inside the PCB will be half of that in free
space. Thus even the smallest PCBs may have unexpected resonances.
相關PDF資料 |
PDF描述 |
|---|---|
| V23833-F0005-B101 | XFP850 nm Small Form Factor Module 10 Gigabit Pluggable Transceiver Compatible with XFP MSA Rev. 3.1 |
| V23833-F0005-B102 | XFP850 nm Small Form Factor Module 10 Gigabit Pluggable Transceiver Compatible with XFP MSA Rev. 3.1 |
| V23833-F9909-Z001 | 10 Gigabit XFP SerialHot-Pluggable Transceiver |
| V23833-FX105-B001 | XFP1310 nm Small Form Factor Module 10 Gigabit Pluggable Transceiver Compatible with XFP MSA Rev. 3.1 |
| V23833-G2104-A001 | XPAK 1310 nm Module 10 Gigabit Pluggable Transceiver Compatible with XPAK MSA Rev. 2.3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| V23832-T2531-M101 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:PAROLI 2 Tx AC, 1.25 Gbit/s |
| V23833-D6005-A001 | 功能描述:TRANSCEIVER 850NM 10G ETHERNET RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:25 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 供應商設備封裝:16-PDIP 包裝:管件 |
| V23833-D9909-Z100 | 制造商:Infineon Technologies AG 功能描述:CAGE ASSEMBLY KIT |
| V23833-F0005-B101 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:XFP850 nm Small Form Factor Module 10 Gigabit Pluggable Transceiver Compatible with XFP MSA Rev. 3.1 |
| V23833-F0005-B102 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:XFP850 nm Small Form Factor Module 10 Gigabit Pluggable Transceiver Compatible with XFP MSA Rev. 3.1 |
發布緊急采購，3分鐘左右您將得到回復。