- 您現在的位置：買賣IC網 > PDF目錄359352 > VCO-600A (Vectron International, Inc.) Voltage Controlled Saw Oscillator PDF資料下載
參數資料
| 型號： | VCO-600A |
| 廠商： | Vectron International, Inc. |
| 元件分類： | 振蕩器 |
| 英文描述： | Voltage Controlled Saw Oscillator |
| 中文描述： | 壓控SAW振蕩器 |
| 文件頁數： | 3/6頁 |
| 文件大?。?/td> | 123K |
| 代理商： | VCO-600A |
VCO-600A Voltage Controlled SAW Oscillator
Vectron International 267 Lowell Rd, Hudson NH 03051-4916 Tel:1-88-VECTRON-1 e-mail vectron@vectron.com
3
Figure 1. PECL Operation
Figure 2. ECL Operation
1. By setting OD low, a test signal may be applied at CLKIN and fed through the VCO-600A to both the CLKOUT and CLKOUT to facilitate on board
testing. The test signal input applied at CLKIN may be either an ECL or sinewave input (up to 1Vpp, AC coupled). CLKIN is biased internally to
VBB (Vcc-1.3V)
2. An optional capacitor to ground can be placed on VBW to reduce the modulation bandwidth for narrow bandwidth phase-lock loop applications. The
modulation bandwidth will be approximately 1/(12000*C) Hz, where C is equal to the capacitance in Farads. If the optional capacitor is not utilized, VBW
becomes a no connect (NC) and the modulation bandwidth will be approximately equal to the nominal device frequency
÷
1200.
3. By setting OD low, the outputs are disabled and CLKOUT is held Low while CLKOUT is held High. The threshold for OD is 1.4V above VEE. OD
should not be driven above mid supply and during normal operation, should be left floating (use with an open collector or 3-State gate for interfacing with
standard logic). If the OD feature is used during normal operation, then CLKIN should be tied through 10K
to GND to avoid any possibility of chatter on
the CLKOUT outputs
17
V
EE
VCO-600A
OUT
Control Voltage
OUT
Output Disable
Test Clock In
V
CC Ground
-2V, 50ohms
-5 V
-4.5 to -0.5V
10
19
21
4
2,12,27
1,3,9,11,13,14,15,16,18,20,22,24,26,28
17
V
CC
VCO-600A
OUT
Control Voltage
OUT
Output Disable
Test Clock In
V
EE Ground
+3V, 50ohms
+5 V
0.5 to 4.5V
2,12,27
19
21
4
10
1,3,9,11,13,14,15,16,18,20,22,24,26,28
23
25
23
25
Optional
Capacitor
Reduces
Bandwidth
Optional
Capacitor
Reduces
Bandwidth
相關PDF資料 |
PDF描述 |
|---|---|
| VCO190-450AT | VCO Product Specification |
| VCR11N | N-CHANNEL JFET VOLTAGE CONTROLLED RESISTOR |
| VCR11 | N-Channel Silicon Voltage Controlled Resistor JFET |
| VCR11N | N-Channel Silicon Voltage Controlled Resistor JFET |
| VCR2N | JFET Voltage-Controlled Resistor(最大柵源擊穿電壓-7V，最大導通電阻60Ω的N溝道結型場效應管) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VCO600A155.52MHZ | 制造商:VECTRON 制造商全稱:Vectron International, Inc 功能描述:Voltage Controlled Saw Oscillator |
| VCO600A278.528MHZ | 制造商:VECTRON 制造商全稱:Vectron International, Inc 功能描述:Voltage Controlled Saw Oscillator |
| VCO600A278.852MHZ | 制造商:VECTRON 制造商全稱:Vectron International, Inc 功能描述:Voltage Controlled Saw Oscillator |
| VCO600A311.040MHZ | 制造商:VECTRON 制造商全稱:Vectron International, Inc 功能描述:Voltage Controlled Saw Oscillator |
| VCO600A368.640MHZ | 制造商:VECTRON 制造商全稱:Vectron International, Inc 功能描述:Voltage Controlled Saw Oscillator |
發布緊急采購，3分鐘左右您將得到回復。