- 您現在的位置：買賣IC網 > PDF目錄359398 > VN06SP13TR (意法半導體) ISO HIGH SIDE SMART POWER SOLID STATE RELAY PDF資料下載
參數資料
| 型號： | VN06SP13TR |
| 廠商： | 意法半導體 |
| 英文描述： | ISO HIGH SIDE SMART POWER SOLID STATE RELAY |
| 中文描述： | 標準高邊智能電源固態繼電器 |
| 文件頁數： | 5/9頁 |
| 文件大小： | 219K |
| 代理商： | VN06SP13TR |
FUNCTIONAL DESCRIPTION
The device has a diagnostic output which
indicates open load conditions in off state as well
as in on state, output shorted to V
CC
and
overtemperature. The truth table shows input,
diagnostic and output voltage level in normal
operation and in fault conditions. The output
signals are processed by internal logic. The
open load diagnostic output has a 5 ms filtering.
The filter gives a continuous signal for the fault
condition after an initial delay of about 5 ms. This
means that a disconnection during normal
operation, with a duration of less than 5 ms does
not affect the status output. Equally, any
re-connection of less than 5 ms during a
disconnection duration does not affect the status
output. No delay occur for the status to go low in
case of overtemperature conditions. From the
falling edge of the input signal the status output
initially low in fault condition (over temperature or
open load) will go back with a delay (t
povl
)in case
of overtemperature condition and a delay (t
pol
) in
case of open load. These feature fully comply
with
International
Standard
requirement for automotive High Side Driver.
To protect the device against short circuit and
over current conditions, the thermal protection
turns the integrated Power MOS off at a
minimum junction temperature of 140
o
C.
When the temperature returns to 125
o
C the
switch is automatically turned on again. In short
circuit the protection reacts with virtually no
delay, the sensor being located in the region of
the die where the heat is generated. Driving
inductive loads, an internal function of the
device ensures the fast demagnetization with a
Office
(I.S.O.)
typical voltage (V
demag
) of -18V.
This function allows to greatly reduce the power
dissipation according to the formula:
P
dem
= 0.5
L
load
(I
load
)
2
[(V
CC
+V
demag
)/V
demag
]
f
where f = switching frequency and
V
demag
= demagnetization voltage
Based on this formula it is possible to know
the value of inductance and/or current to avoid
a thermal shut-down. The maximum inductance
which causes the chip temperature to reach the
shut down temperature in a specific thermal
environment, is infact a function of the load
current for a fixed V
CC
, V
demag
and f.
PROTECTING THE DEVICE AGAIST LOAD
DUMP - TEST PULSE 5
The device is able to withstand the test pulse
No. 5 at level II (V
s
= 46.5V) according to the
ISO T/R 7637/1 without any external
component. This means that all functions of the
device are performed as designed after
exposure to disturbance at level II. The VN06SP
is able to withstand the test pulse No.5 at level
III adding an external resistor of 150 ohm
between GND pin and ground plus a filter
capacitor of 1000
μ
F between V
CC
pin and
ground (if R
LOAD
≤
20
).
PROTECTING THE DEVICE AGAINST
REVERSE BATTERY
The simplest way to protect the device against a
continuous reverse battery voltage (-26V) is to
insert a Schottky diode between GND pin and
ground, as shown in the typical application circuit
(fig.3).
The consequences of the voltage drop across
this diode are as follows:
If the input is pulled to power GND, a negative
voltage of -V
f
is seen by the device. (Vil, Vih
thresholds and Vstat are increased by Vf with
respect to power GND).
The undervoltage shutdown level is increa- sed
by Vf.
If there is no need for the control unit to handle
external analog signals referred to the power
GND, the best approach is to connect the
reference potential of the control unit to node [6]
(see application circuit in fig. 4), which becomes
the common signal GND for the whole control
board avoiding shift of V
ih
, V
il
and V
stat
. This
solution allows the use of a standard diode.
Switching Time Waveforms
VN06SP
5/9
相關PDF資料 |
PDF描述 |
|---|---|
| VN06SP | ISO High Side Smart Power Solid State Relay(ISO 高邊智能化功率固態繼電器) |
| VN06 | ISO HIGH SIDE SMART POWER SOLID STATE RELAY |
| VN0808L | N-Channel Enhancement-Mode MOSFET Transistor(最小漏源擊穿電壓80V，夾斷電流0.3A的N溝道增強型MOSFET) |
| VN0808L | N-Channel 80- and 90-V (D-S) MOSFETs |
| VN0808LS | N-Channel 80- and 90-V (D-S) MOSFETs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VN06SP-E | 功能描述:電源開關 IC - 配電 HIGH SIDE FOR SSR RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| VN06SPTR-E | 功能描述:固態繼電器-PCB安裝 HI-SIDE SMART PWR SOLID STATE RELAY RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| VN0808 | 制造商:SUPERTEX 制造商全稱:SUPERTEX 功能描述:N-Channel Enhancement-Mode Vertical DMOS FETs |
| VN0808L | 功能描述:MOSFET 80V 0.3A 0.8W RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| VN0808L-G | 功能描述:MOSFET 80V 4Ohm RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。