參數資料
型號： W3H64M72E-667SBCF
廠商： WHITE ELECTRONIC DESIGNS CORP
元件分類： DRAM
英文描述： 64M X 72 DDR DRAM, PBGA208
封裝： 16 X 22 MM, 1 MM PITCH, LEAD FREE, PLASTIC, BGA-208
文件頁數： 2/32頁
文件大?。?/td> 944K
代理商： W3H64M72E-667SBCF
W3H64M72E-XSBX
W3H64M72E-XSBXF
10
White Electronic Designs Corporation (602) 437-1520 www.whiteedc.com
White Electronic Designs
December 2009
2010 White Electronic Designs Corp. All rights reserved
Rev. 9
White Electronic Designs Corp. reserves the right to change products or specications without notice.
TABLE 2 – BURST DEFINITION
NOTES:
1.
For a burst length of two, A1-Ai select two-data-element block; A0 selects the
starting column within the block.
2.
For a burst length of four, A2-Ai select four-data-element block; A0-1 select the
starting column within the block.
3.
For a burst length of eight, A3-Ai select eight-data-element block; A0-2 select the
starting column within the block.
4.
Whenever a boundary of the block is reached within a given sequence above, the
following access wraps within the block.
Burst
Length
Starting Column
Address
Order of Accesses Within a Burst
Type = Sequential
Type = Interleaved
4
A1
A0
0
0-1-2-3
0
1
1-2-3-0
1-0-3-2
1
0
2-3-0-1
1
3-0-1-2
3-2-1-0
8
A2
A1
A0
0
0-1-2-3-4-5-6-7
0
1
1-2-3-0-5-6-7-4
1-0-3-2-5-4-7-6
0
1
0
2-3-0-1-6-7-4-5
0
1
3-0-1-2-7-4-5-6
3-2-1-0-7-6-5-4
1
0
4-5-6-7-0-1-2-3
1
0
1
5-6-7-4-1-2-3-0
5-4-7-6-1-0-3-2
1
0
6-7-4-5-2-3-0-1
1
7-4-5-6-3-0-1-2
7-6-5-4-3-2-1-0
OPERATING MODE
The normal operating mode is selected by issuing a
command with bit M7 set to “0,” and all other bits set to
the desired values, as shown in Figure 5. When bit M7 is
“1,” no other bits of the mode register are programmed.
Programming bit M7 to “1” places the DDR2 SDRAM into a
test mode that is only used by the manufacturer and should
not be used. No operation or functionality is guaranteed
if M7 bit is ‘1.’
DLL RESET
DLL RESET is dened by bit M8, as shown in Figure 5.
Programming bit M8 to “1” will activate the DLL RESET
function. Bit M8 is self-clearing, meaning it returns back
to a value of “0” after the DLL RESET function has been
issued.
Anytime the DLL RESET function is used, 200 clock cycles
must occur before a READ command can be issued to
allow time for the internal clock to be synchronized with
the external clock. Failing to wait for synchronization
to occur may result in a violation of the tAC or tDQSCK
parameters.
WRITE RECOVERY
Write recovery (WR) time is dened by bits M9–M11, as
shown in Figure 5. The WR register is used by the DDR2
SDRAM during WRITE with auto precharge operation.
During WRITE with auto precharge operation, the DDR2
SDRAM delays the internal auto precharge operation by
WR clocks (programmed in bits M9–M11) from the last
data burst.
WR values of 2, 3, 4, 5, or 6 clocks may be used for
programming bits M9–M11. The user is required to
program the value of WR, which is calculated by dividing
t
WR (in ns) by tCK (in ns) and rounding up a non integer
value to the next integer; WR [cycles] = tWR [ns] / tCK [ns].
Reserved states should not be used as unknown operation
or incompatibility with future versions may result.
POWER-DOWN MODE
Active power-down (PD) mode is dened by bit M12,
as shown in Figure 5. PD mode allows the user to
determine the active power-down mode, which determines
performance versus power savings. PD mode bit M12 does
not apply to precharge PD mode.
When bit M12 = 0, standard active PD mode or “fast-exit”
active PD mode is enabled. The tXARD parameter is used
for fast-exit active PD exit timing. The DLL is expected to
be enabled and running during this mode.
When bit M12 = 1, a lower-power active PD mode or “slow-
exit” active PD mode is enabled. The tXARD parameter is
used for slow-exit active PD exit timing. The DLL can be
enabled, but “frozen” during active PD mode since the exit-
to-READ command timing is relaxed. The power difference
expected between PD normal and PD low-power mode is
dened in the ICC table.
相關PDF資料
PDF描述
WS512K32-25G4C 2M X 8 MULTI DEVICE SRAM MODULE, 25 ns, CQFP68
WS1M8V-17CM 1M X 8 STANDARD SRAM, 17 ns, CDIP32
WS1M8V-20CC 1M X 8 STANDARD SRAM, 20 ns, CDIP32
WS1M8V-35CC 1M X 8 STANDARD SRAM, 35 ns, CDIP32
WS256K8-25CQE 256K X 8 MULTI DEVICE SRAM MODULE, 25 ns, CDMA32
相關代理商/技術參數
參數描述
W3H64M72E-667SBI 制造商:Microsemi Corporation 功能描述:64M X 72 DDR2, 1.8V, 667MHZ, 208PBGA INDUSTRIAL TEMP. - Bulk
W3H64M72E-667SBM 制造商:Microsemi Corporation 功能描述:64M X 72 DDR2, 1.8V, 667MHZ, 208PBGA MIL-TEMP. - Bulk 制造商:Microsemi Corporation 功能描述:SDRAM MEMORY
W3H64M72EERXXXAD7MG 制造商:WEDC 制造商全稱:White Electronic Designs Corporation 功能描述:512MB - 64Mx72 DDR2 SDRAM REGISTERED, w/PLL, VLP Mini-DIMM
W3H64M72EERXXXAD7SG 制造商:WEDC 制造商全稱:White Electronic Designs Corporation 功能描述:512MB - 64Mx72 DDR2 SDRAM REGISTERED, w/PLL, VLP Mini-DIMM
W3H64M72E-ES 制造商:WEDC 制造商全稱:White Electronic Designs Corporation 功能描述:64M x 72 DDR2 SDRAM 208 PBGA Multi-Chip Package
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*