- 您現在的位置：買賣IC網 > PDF目錄371197 > X24001SI-3 Identi⑩PROM PDF資料下載
參數資料
| 型號： | X24001SI-3 |
| 英文描述： | Identi⑩PROM |
| 中文描述： | 認⑩胎膜早破 |
| 文件頁數： | 5/13頁 |
| 文件大?。?/td> | 47K |
| 代理商： | X24001SI-3 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁
X24001
5
Read Operation
The byte read operation is initiated with a start condition.
The start condition is followed by an eight-bit control byte
which consists of a two-bit read command (1,0), four
address bits, and two “don’t care” bits. After receipt of
the control byte, the X24001 will enter the read mode
and transfer data into the shift register from the array.
This data is shifted out of the device on the next eight
SCL clocks. At the end of the read, all counters are reset
and the X24001 will enter the standby mode. As with a
write, the read operation can be interrupted by a start or
stop condition while the command or address is being
clocked in. While clocking data out, starts or stops
cannot be generated.
During the second don’t care clock cycle, starts and
stops are ignored. The master must free the bus prior to
the end of this clock cycle to allow the X24001 to begin
outputting data (Figures 4 and 5).
3830 FHD F07
Figure 4. Read Sequence
3830 FHD F06
Figure 5. Read Cycle Timing
6
7
8
1
SDA IN
SCK
SDA OUT
A0
XX
XX
D7
D6
START
1
0
A3
A2
A1
A0
XX XX D7
D6
D5
D4
D3
D2
D1
D0
SYMBOL TABLE
WAVEFORM
INPUTS
OUTPUTS
Must be
steady
Will be
steady
May change
from LOW
to HIGH
Will change
from LOW
to HIGH
May change
from HIGH
to LOW
Will change
from HIGH
to LOW
Don’t Care:
Changes
Allowed
N/A
Changing:
State Not
Known
Center Line
is High
Impedance
相關PDF資料 |
PDF描述 |
|---|---|
| X24022PM-2.7 | Serial E2PROM |
| X24022PM-3 | AC/DC CAPACITANCE=3 VOLT=600 |
| X24022SI-2.7 | Serial E2PROM |
| X24022SI-3 | Serial E2PROM |
| X24022SM-2.7 | Serial E2PROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X24001SM | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Identi⑩PROM |
| X24001SM-2.7 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Identi⑩PROM |
| X24001SM-3 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Identi⑩PROM |
| X24-009-DK | 功能描述:射頻開發工具 2.4 GHz - Xstream 9600 BAUD RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V |
| X24-009-DK-INT | 制造商:Digi International 功能描述:XSTREAM DEVELOPMENT KIT, 2.4GHZ, 50MW, 9600 BAUD, 3" WIRE & - Boxed Product (Development Kits) 制造商:Digi International Inc 功能描述:KIT DEV XSTREAM 2.4GHZ 50MW 制造商:Digi International Inc 功能描述:Xstream Dev Kit 制造商:Digi International 功能描述:Xstream 2.4GHz Modem Dev kit 9600 Baud |
發布緊急采購，3分鐘左右您將得到回復。