參數資料
型號: X24325VM-2.7
英文描述: Advanced 2-Wire Serial E 2 PROM with Block Lock TM Protection
中文描述: 先進的2線串行e的2座門鎖TM保護胎膜早破
文件頁數: 9/17頁
文件大?。?/td> 79K
代理商: X24325VM-2.7
X24325
9
WRITE PROTECT REGISTER
The Write Protect Register (WPR) is located at the
highest address, FFFh.
Figure 11. Write Protect Register
WPR.1 = WEL
Write Enable Latch (Volatile)
0 = Write enable latch reset, writes disabled
1 = Write enable latch set, writes enabled
If WEL = 0 then “no ACK” after first byte of input data.
WPR.2 = RWEL
Register Write Enable Latch (Volatile)
0 = Register write enable latch reset, writes dis-
abled
1 = Register write enable latch set, writes enabled
WPR.3, WPR.4 = BP0, BP1
Block Protect Bits (Nonvolatile)
(See Block Protect section for definition)
WPR.7 = WPEN
Write Protect Enable Bit (Nonvolatile)
(See Hardware Write Protect section for definition)
Writing to the Write Protect Register
The Write Protect Register is written by performing a
random write of one byte directly to address, FFFh. If a
page write is performed starting with any address
other than FFFh, the byte in the array at address FFFh
will be written instead of the Write Protect Register
(assuming writes are not disabled by the block protect
register).
The state of the Write Protect Register can be read by
performing a random read at address FFFh at any
time. If a sequential read starting at any other address
than FFFh is performed, the contents of the byte in the
array at FFFh is read out instead of the Write Protect
Register.
7
6
5
4
3
2
1
0
WPEN
0
0
BP1
BP0
RWEL
WEL
0
6552 ILL F15
WPR (Addr = FFFh)
WEL and RWEL are volatile latches that power-up in
the LOW (disabled) state. A write to any address other
than FFFh, where the Write Protect Register is
located, will be ignored (no ack) until the WEL bit is set
HIGH. The WEL bit is set by writing 0000001x to
address FFFh. Once set, WEL remains HIGH until
either reset (by writing 00000000 to FFFh) or until the
part powers-up again. The RWEL bit controls writes to
the block protect bits. RWEL is set by first setting WEL
= 1 and then writing 0000011x to address FFFh.
RWEL must be set in order to change the block protect
bits, BP0 and BP1, or the WPEN bit. RWEL is reset
when the block protect or WPEN bits are changed, or
when the part powers-up again.
Programming the BP or WPEN Bits
A three step sequence is required to change the
nonvoltaile Block Protect or Write Protect Enable:
1) Set WEL = 1 (write 00000010 to address FFFh,
volatile write cycle)
(Start)
2) Set RWEL = 1 (write 00000110 to address FFFh,
volatile write cycle)
(Start)
3) Set BP1, BP0, and/or WPEN bits (Write w00yz010
to address FFFh)
w = WPEN, y = BP1, Z = BP0,
(Stop)
Step 3 is a nonvolatile write cycle, requiring 10ms to
complete. RWEL is reset (0) by this write cycle,
requiring another write cycle to set RWEL again before
the block protect bits can be changed. RWEL must be
0 in step 3; if w00yz110 is written to address FFFh,
RWEL is set but WPEN, BP1 and BP0 are not
changed (the device remains at step 2).
相關PDF資料
PDF描述
X24325P-2.7 Advanced 2-Wire Serial E 2 PROM with Block Lock TM Protection
X24325 Advanced 2-Wire Serial E 2 PROM with Block Lock TM Protection
X24325P Advanced 2-Wire Serial E 2 PROM with Block Lock TM Protection
X24325PI IC ADJ SHUNT REG LV SOT-23-3
X24325PM IC ADJ SHUNT REG LV SOT-23-3
相關代理商/技術參數
參數描述
X243-883B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:X200 SERIES (CMOS) STANDARD SPECFITIONS
X243-SERIES 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC
X-24-428-SVBB-BK 制造商:Brady Corporation 功能描述:Labels External Height:0.5" 制造商:Brady Corporation 功能描述:LABEL IDENTIFICATION 29X12.7 BLK/SILVER; Background Color:Silver; Color:Black on Silver; External Height:0.5"; External Width:1.13"; For Use With:IDXPERT Hand-Held Labeler; Label Material:Metalized Polyester; Label Size:28.7 x 12.7mm;RoHS Compliant: Yes
X2444P 制造商:Intersil Corporation 功能描述: 制造商:XICOR 功能描述: 制造商:Intersil Corporation 功能描述:Non-Volatile RAM, 16 x 16, 8 Pin, Plastic, DIP
X2444P1 制造商:undefined 功能描述: