- 您現在的位置：買賣IC網 > PDF目錄371225 > X25F128SE-5 SerialFlash⑩ Memory With Block Lock⑩ Protection PDF資料下載
參數資料
| 型號： | X25F128SE-5 |
| 英文描述： | SerialFlash⑩ Memory With Block Lock⑩ Protection |
| 中文描述： | SerialFlash⑩內存區塊可鎖定的⑩保護 |
| 文件頁數： | 2/14頁 |
| 文件大小： | 61K |
| 代理商： | X25F128SE-5 |
2
X25F128
Hold (
HOLD
)
HOLD
is used in conjunction with the
CS
pin to select the
device. Once the part is selected and a serial sequence
is underway,
HOLD
may be used to pause the serial
communication with the controller without resetting the
serial sequence. To pause,
HOLD
must be brought
LOW while SCK is LOW. To resume communication,
HOLD
is brought HIGH, again while SCK is LOW. If the
pause feature is not used,
HOLD
should be held HIGH
at all times.
PIN NAMES
SYMBOL
DESCRIPTION
CS
SO
SI
SCK
PP
V
SS
V
CC
HOLD
NC
Chip Select Input
Serial Output
Serial Input
Serial Clock Input
Program Protect Input
Ground
Supply Voltage
Hold Input
No Connect
6829 PGM T01
PIN DESCRIPTIONS
Serial Output (SO)
SO is a push-pull serial data output pin. During a read
cycle, data is shifted out on this pin. Data is clocked out
by the falling edge of the serial clock.
Serial Input (SI)
SI is the serial data input pin. All opcodes, byte
addresses, and data to be written to the memory are
input on this pin. Data is latched by the rising edge of the
serial clock.
Serial Clock (SCK)
The Serial Clock controls the serial bus timing for data
input and output. Opcodes, addresses, or data present
on the SI pin are latched on the rising edge of the clock
input, while data on the SO pin change after the falling
edge of the clock input.
Chip Select (
CS
)
When
CS
is HIGH, the X25F128 is deselected and the
SO output pin is at high impedance and unless an
internal program operation is underway the X25F128
will be in the standby power mode.
CS
LOW enables
the X25F128, placing it in the active power mode. It
should be noted that after power-up, a HIGH to LOW
transition on
CS
is required prior to the start of any
operation.
Program Protect (
PP
)
When
PP
is LOW and the nonvolatile bit PPEN is “1”,
nonvolatile programming of the X25F128 status register
is disabled, but the part otherwise functions normally.
When
PP
is held HIGH, all functions, including nonvola-
tile programming operate normally.
PP
going LOW while
CS
is still LOW will interrupt programming of the
X25F128 status register. If the internal program cycle
has already been initiated,
PP
going LOW will have no
effect on programming.
The
PP
pin function is blocked when the PPEN bit in
the status register is “0”. This allows the user to install the
X25F128 into a system with
PP
pin grounded and still
be able to program the status register. The
PP
pin
functions will be enabled when the PPEN bit is set “0”.
PIN CONFIGURATION
6829 ILL F02.1
CS
SO
PP
VSS
1
2
3
4
8
7
6
5
VCC
HOLD
SCK
SI
8-LEAD DIP
16-LEAD SOIC
CS
SO
NC
NC
NC
NC
PP
VSS
1
2
3
4
5
6
7
8
VCC
HOLD
NC
NC
NC
NC
SCK
SI
16
15
14
13
12
11
10
9
X25F128
X25F128
相關PDF資料 |
PDF描述 |
|---|---|
| X2804A | ELECTRICALLY ERASBLE PROM |
| X2804AI | ELECTRICALLY ERASBLE PROM |
| X2804ADI | 128Kx8 EEPROM |
| X2804ADI-25 | 128Kx8 EEPROM |
| X2804ADI-35 | 128Kx8 EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X25F128SI | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:SerialFlash⑩ Memory With Block Lock⑩ Protection |
| X25F128SI-5 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:SerialFlash⑩ Memory With Block Lock⑩ Protection |
| X25FG | 制造商:VMI 制造商全稱:VMI 功能描述:2,500 V - 10,000 V Rectifiers 100 mA - 250 mA Forward Current 200 ns Recovery Time |
| X25M000000S054 | 制造商:AEL Crystals Limited 功能描述:CRYSTAL SM 25MHZ 2.5X2 |
| X25RT | 制造商:Burndy 功能描述:HARDWARE TOOLS, BURNDY PRODUCTS TOOLING |
發布緊急采購，3分鐘左右您將得到回復。