參數資料
型號： X4285AL
英文描述： LABELS,CABLE MARKERS,CABLE MARKERS,LABELS, CABLE MARKERS,IDENTIFICATION PRODUCTS,PAN-CODE? WIRE MARKER BOOKS ,PANDUIT
中文描述： CPU監控與128K的EEPROM的
文件頁數： 12/22頁
文件大?。?/td> 412K
代理商： X4285AL
X4283/85 – Preliminary Information
Characteristics subject to change without notice.
12 of 22
REV 1.17 11/27/00
www.xicor.com
There is a similar operation, called “Set Current
Address” where the device does no operation, but
enters a new address into the address counter if a stop
is issued instead of the second start shown in Figure
13. The device goes into standby mode after the stop
and all bus activity will be ignored until a start is
detected. The next Current Address Read operation
reads from the newly loaded address. This operation
could be useful if the master knows the next address it
needs to read, but is not ready for the data.
Sequential Read
Sequential reads can be initiated as either a current
address read or random address read. The first Data
Byte is transmitted as with the other modes; however,
the master now responds with an acknowledge,
indicating it requires additional data. The device contin-
ues to output data for each acknowledge received. The
master terminates the read operation by not responding
with an acknowledge and then issuing a stop condition.
The data output is sequential, with the data from
address n followed by the data from address n + 1. The
address counter for read operations increments
through all page and column addresses, allowing the
entire memory contents to be serially read during one
operation. At the end of the address space the counter
“rolls over” to address 0000
H
and the device continues
to output data for each acknowledge received. Refer to
Figure 14 for the acknowledge and data transfer
sequence.
Figure 14. Sequential Read Sequence
Data
(2)
S
t
o
p
Slave
Address
Data
(n)
A
C
K
A
C
K
SDA Bus
Signals from
the Slave
Signals from
the Master
1
Data
(n-1)
A
C
K
A
C
K
(n is any integer greater than 1)
Data
(1)
X4283/85 Addressing
S
LAVE
A
DDRESS
B
YTE
Following a start condition, the master must output a
Slave Address Byte. This byte consists of several parts:
– a device type identifier that is ‘1010’ to access the array
– one bits of ‘0’.
– next two bits are the device address.
– one bit of the slave command byte is a R/W bit. The
R/W bit of the Slave Address Byte defines the opera-
tion to be performed. When the R/W bit is a one, then
a read operation is selected. A zero selects a write
operation. Refer to Figure 15.
– After loading the entire Slave Address Byte from the
SDA bus, the device compares the input slave byte
data to the proper slave byte. Upon a correct compare,
the device outputs an acknowledge on the SDA line.
Word Address
The word address is either supplied by the master or
obtained from an internal counter. The internal counter
is undefined on a power up condition.
相關PDF資料
PDF描述
X4285AM CPU Supervisor with 128K EEPROM
X4283AL CPU Supervisor with 128K EEPROM
X4283AN CPU Supervisor with 128K EEPROM
X4283AP CPU Supervisor with 128K EEPROM
X4283S8-2.7 CPU Supervisor with 128K EEPROM
相關代理商/技術參數
參數描述
X4285AM 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:CPU Supervisor with 128K EEPROM
X4285AN 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:CPU Supervisor with 128K EEPROM
X4285AP 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:CPU Supervisor with 128K EEPROM
X4285F 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:CPU Supervisor with 128K EEPROM
X4285G 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:CPU Supervisor with 128K EEPROM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*