參數資料
型號: X4285AL
英文描述: LABELS,CABLE MARKERS,CABLE MARKERS,LABELS, CABLE MARKERS,IDENTIFICATION PRODUCTS,PAN-CODE? WIRE MARKER BOOKS ,PANDUIT
中文描述: CPU監控與128K的EEPROM的
文件頁數: 9/22頁
文件大?。?/td> 412K
代理商: X4285AL
X4283/85 – Preliminary Information
Characteristics subject to change without notice.
9 of 22
REV 1.17 11/27/00
www.xicor.com
Serial Write Operations
B
YTE
W
RITE
For a write operation, the device requires the Slave
Address Byte and a Word Address Byte. This gives the
master access to any one of the words in the array. After
receipt of the Word Address Byte, the device responds
with an acknowledge, and awaits the next eight bits of
data. After receiving the 8 bits of the Data Byte, the
device again responds with an acknowledge. The mas-
ter then terminates the transfer by generating a stop
condition, at which time the device begins the internal
write cycle to the nonvolatile memory. During this inter-
nal write cycle, the device inputs are disabled, so the
device will not respond to any requests from the master.
The SDA output is at high impedance. See Figure 8.
Figure 8. Byte Write Sequence
S
t
a
r
t
S
t
o
p
Slave
Address
Word Address
Byte 0
Data
A
C
K
A
C
K
A
C
K
SDA Bus
Signals from
the Slave
Signals from
the Master
0
Word Address
Byte 1
A
C
K
0
1
0
1
A write to a protected block of memory will suppress
the acknowledge bit.
Page Write
The device is capable of a page write operation. It is
initiated in the same manner as the byte write opera-
tion; but instead of terminating the write cycle after the
first data byte is transferred, the master can transmit an
unlimited number of 8-bit bytes. After the receipt of
each byte, the device will respond with an acknowl-
edge, and the address is internally incremented by
one. The page address remains constant. When the
counter reaches the end of the page, it “rolls over” and
goes back to ‘0’ on the same page. This means that the
master can write 64 bytes to the page starting at any
location on that page. If the master begins writing at
location 60, and loads 12 bytes, then the first 4 bytes
are written to locations 60 through 63, and the last 8
bytes are written to locations 0 through 7. Afterwards,
the address counter would point to location 8 of the
page that was just written. If the master supplies more
than 64 bytes of data, then new data over-writes the
previous data, one byte at a time.
Figure 9. Page Write Operation
S
t
a
r
t
S
t
o
p
Slave
Address
Word Address
Byte 1
Data
(n)
A
C
K
A
C
K
A
C
K
SDA Bus
Signals from
the Slave
Signals from
the Master
0
Data
(1)
A
C
K
(1 < n < 64)
Word Address
Byte 0
A
C
K
1
0
1
0
相關PDF資料
PDF描述
X4285AM CPU Supervisor with 128K EEPROM
X4283AL CPU Supervisor with 128K EEPROM
X4283AN CPU Supervisor with 128K EEPROM
X4283AP CPU Supervisor with 128K EEPROM
X4283S8-2.7 CPU Supervisor with 128K EEPROM
相關代理商/技術參數
參數描述
X4285AM 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:CPU Supervisor with 128K EEPROM
X4285AN 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:CPU Supervisor with 128K EEPROM
X4285AP 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:CPU Supervisor with 128K EEPROM
X4285F 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:CPU Supervisor with 128K EEPROM
X4285G 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:CPU Supervisor with 128K EEPROM