- 您現在的位置：買賣IC網 > PDF目錄372536 > x76f102 4 Mbit Uniform Sector, Serial Flash Memory PDF資料下載
參數資料
| 型號： | x76f102 |
| 元件分類： | FLASH |
| 英文描述： | 4 Mbit Uniform Sector, Serial Flash Memory |
| 中文描述： | 4兆位統一部門，串行閃存 |
| 文件頁數： | 5/18頁 |
| 文件大小： | 104K |
| 代理商： | X76F102 |
X76F102
5
the new command code of 8 bits (1st byte of the proto-
col.) If the X76F102 is still busy with the nonvolatile write
operation, it will issue a “no-ACK” in response. If the non-
volatile write operation has completed, an “ACK” will be
returned and the host can then proceed with the rest of
the protocol.
Data ACK Polling Sequence
After the password sequence, there is always a nonvola-
tile write cycle. This is done to discourage random
guesses of the password if the device is being tampered
with. In order to continue the transaction, the X76F102
requires the master to perform a password ACK polling
sequence with the specific command code of 55h. As
with regular Acknowledge polling the user can either time
out for 10ms, and then issue the ACK polling once, or
continuously loop as described in the flow.
If the password that was inserted was correct, then an
“ACK” will be returned once the nonvolatile cycle in
response to the passwrod ACK polling sequence is over.
If the password that was inserted was incorrect, then a
“no ACK” will be returned even if the nonvolatile cycle is
over. Therefore, the user cannot be certain that the pass-
word is incorrect until the 10ms write cycle time has
elapsed.
READ OPERATIONS
Read operations are initiated in the same manner as
write operations but with a different command code.
Sector Read
With sector read, a sector address is supplied with the
read command. Once the password has been acknowl-
edged data may be read from the sector. An acknowl-
edge must follow each 8-bit data transfer. A read
operation always begins at the first byte in the sector, but
may stop at any time. Random accesses to the array are
not possible. Continuous reading from the array will
return data from successive sectors. After reading the
last sector in the array, the address is automatically set to
the first sector in the array and data can continue to be
read out. After the last bit has been read, a stop condition
is generated without sending a preceding acknowledge.
ACK
RETURNED
ISSUE NEW
COMMAND
CODE
Write sequence completed
Enter ACK Polling
ISSUE START
NO
YES
PROCEED
Password ACK Polling Sequence
ACK
RETURNED
ISSUE
PASSWORD
ACK COMMAND
PASSWORD LOAD
COMPLETED
ENTER ACK POLLING
ISSUE START
NO
YES
PROCEED
相關PDF資料 |
PDF描述 |
|---|---|
| X76F128(中文) | Secure SerialFlash(位密度128K，對復位的同步響應；二線串口；允許任意數目的器件共享同一總線) |
| x76f200 | Secure SerialFlash(密碼訪問加密串行EEPROM) |
| x76f400 | Secure SerialFlash(密碼訪問加密串行EEPROM) |
| X76F640(中文) | Secure SerialFlash(5種64位密碼保護；對復位的同步響應；二線串口；允許任意數目的器件共享同一總線) |
| X7AH-01C | NON-ISOLATED DC/DC CONVERTERS 3 V-3.6 V Input 12 V/0.8 A & 15 V/0.6 A Output |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X76F102H | 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Secure SerialFlash |
| X76F102H-2 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:The X76F102 is a Password Access Security Supervisor, containing one 896-bit Secure SerialFlash array |
| X76F102H-2.0 | 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Secure SerialFlash |
| X76F102HG | 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Secure SerialFlash |
| X76F102HG-2.0 | 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:Secure SerialFlash |
發布緊急采購，3分鐘左右您將得到回復。