- 您現在的位置：買賣IC網 > PDF目錄9207 > X9111TV14IZ-2.7T1 (Intersil)IC POT DGTL 100K OHM 14-TSSOP PDF資料下載
參數資料
| 型號： | X9111TV14IZ-2.7T1 |
| 廠商： | Intersil |
| 文件頁數： | 12/17頁 |
| 文件大小： | 0K |
| 描述： | IC POT DGTL 100K OHM 14-TSSOP |
| 標準包裝： | 1 |
| 系列： | XDCP™ |
| 接片： | 1024 |
| 電阻（歐姆）： | 100k |
| 電路數： | 1 |
| 溫度系數： | 標準值 ±300 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | 6 線 SPI（芯片選擇，設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 剪切帶 (CT) |
| 其它名稱： | X9111TV14IZ-2.7T1CT |
4
FN8159.4
September 15, 2006
These switches are controlled by a Wiper Counter Register
(WCR). The 10-bits of the WCR (WCR[9:0]) are decoded to
select, and enable, one of 1024 switches.
Wiper Counter Register (WCR)
The X9111 contains a Wiper Counter Register (see Table 1)
for the XDCP potentiometer. The WCR is equivalent to a
serial-in, parallel-out register/counter with its outputs
decoded to select one of 1024 switches along its resistor
array. The contents of the WCR can be altered in one of
three ways: (1) it may be written directly by the host via the
write Wiper Counter Register instruction (serial load); (2) it
may be written indirectly by transferring the contents of one
of four associated Data Registers via the XFR Data Register;
(3) it is loaded with the contents of its Data Register zero
(DR0) upon power-up.
The Wiper Counter Register is a volatile register; that is, its
contents are lost when the X9111 is powered-down.
Although the register is automatically loaded with the value
in R0 upon power-up, this may be different from the value
present at power-down. Power-up guidelines are
recommended to ensure proper loadings of the R0 value into
the WCR.
Data Registers (DR3 to DR0)
The potentiometer has four 10-bit non-volatile Data
Registers. These can be read or written directly by the host.
Data can also be transferred between any of the four Data
Registers and the Wiper Counter Register. All operations
changing data in one of the Data Registers is a nonvolatile
operation and will take a maximum of 10ms.
If the application does not require storage of multiple
settings for the potentiometer, the Data Registers can be
used as regular memory locations for system parameters or
user preference data.
A DR[9:0] is used to store one of the 1024 wiper position (0
~1023). Table 2
Status Register (SR)
This 1-bit status register is used to store the system status
(see Table 3).
WIP: Write In Progress status bit, read only.
When WIP=1, indicates that high-voltage write cycle is in
progress.
When WIP=0, indicates that no high-voltage write cycle is
in progress.
Device Instructions
Identification Byte (ID and A)
The first byte sent to the X9111 from the host, following a CS
going HIGH to LOW, is called the Identification Byte. The
most significant four bits of the slave address are a device
type identifier. The ID[3:0] bits is the device ID for the X9111;
this is fixed as 0101[B] (refer to Table 4).
The A1–A0 bits in the ID byte are the internal slave address.
The physical device address is defined by the state of the
A1–A0 input pins. The slave address is externally specified
by the user. The X9111 compares the serial data stream with
the address input state; a successful compare of the address
Serial Data Path
From Interface
Register 0
Serial
Bus
Input
Parallel
Bus
Input
Counter
Register
R H
R L
R
W
10
C
O
U
N
T
E
R
D
E
C
O
D
E
If WCR = 000[HEX] then RW = RL
If WCR = 3FF[HEX] then RW = RH
Wiper
(WCR)
(DR0)
Circuitry
Register 1
(DR1)
Register 2
(DR2)
Register 3
(DR3)
FIGURE 1. DETAILED POTENTIOMETER BLOCK DIAGRAM
X9111
相關PDF資料 |
PDF描述 |
|---|---|
| VE-BTW-MW-B1 | CONVERTER MOD DC/DC 5.5V 100W |
| VE-2VR-MX-B1 | CONVERTER MOD DC/DC 7.5V 75W |
| VE-BTV-MW-B1 | CONVERTER MOD DC/DC 5.8V 100W |
| VE-2V4-MX-B1 | CONVERTER MOD DC/DC 48V 75W |
| IDT74CBTLV3251QG8 | IC MUX/DEMUX 8:1 LV 16-QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9111TV14Z | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9111TV14Z-2.7 | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9116 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Digitally Controlled Potentiometer |
| X9116_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Digitally Controlled Potentiometer |
| X9116_11 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Digitally Controlled Potentiometer |
發布緊急采購，3分鐘左右您將得到回復。