- 您現在的位置：買賣IC網 > PDF目錄1972 > X93254UV14I-3 (Intersil)IC DCP DUAL 50K 32TAP 14-TSSOP PDF資料下載
參數資料
| 型號： | X93254UV14I-3 |
| 廠商： | Intersil |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DCP DUAL 50K 32TAP 14-TSSOP |
| 標準包裝： | 95 |
| 系列： | XDCP™ |
| 接片： | 32 |
| 電阻（歐姆）： | 50k |
| 電路數： | 2 |
| 溫度系數： | 標準值 ±35 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | 6 線串行（芯片選擇，遞增，增/減） |
| 電源電壓： | 2.7 V ~ 3.3 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 管件 |
6
FN8186.1
February 4, 2008
connected in series. At either end of the array and between
each resistor is an electronic switch that transfers the
connection at that point to the wiper.
Each wiper, when at either fixed terminal, acts like its
mechanical equivalent and does not move beyond the last
position. That is, the counter does not wrap around when
clocked to either extreme.
If the wiper is moved several positions, multiple taps are
connected to the wiper for tIW (INC to VW change). The
2-terminal resistance value for the device can temporarily
change by a significant amount if the wiper is moved several
positions.
When the device is powered-down, the last wiper position
stored will be maintained in the nonvolatile memory for each
potentiometer. When power is restored, the contents of the
memory are recalled and each wiper is set to the value last
stored.
Instructions and Programming
The INC, U/D and CS inputs control the movement of the
wiper along the resistor array. With CS set LOW the
potentiometer is selected and enabled to respond to the U/D
and INC inputs. HIGH to LOW transitions on INC will
increment or decrement (depending on the state of the U/D
input) a 5-bit counter. The output of this counter is decoded
to select one of thirty two wiper positions along the resistive
array.
The value of the counter is stored in nonvolatile memory
whenever each CS transitions HIGH while the INC input is
also HIGH. In order to avoid an accidental store during
power-up, each CS must go HIGH with VCC during initial
power-up. When left open, each CS pin is internally pulled up
to VCC by an internal 30k resistor.
The system may select the X93254, move any wiper and
deselect the device without having to store the latest wiper
position in nonvolatile memory. After the wiper movement is
performed as previously described and once the new position
is reached, the system must keep INC LOW while taking CS
HIGH. The new wiper position will be maintained until
changed by the system or until a power-up/down cycle
recalled the previously stored data. In order to recall the
stored position of the wiper on power-up, the CS pin must be
held HIGH.
This procedure allows the system to always power-up to a
preset value stored in nonvolatile memory; then during
system operation minor adjustments could be made. The
adjustments might be based on user preference, system
parameter changes due to temperature drift, or other system
trim requirements.
The state of U/D may be changed while CS remains LOW.
This allows the host system to enable the device and then
move each wiper up and down until the proper trim is
attained.
Symbol Table
Applications Information
Electronic digitally controlled (XDCP) potentiometers provide
three powerful application advantages:
1. The variability and reliability of a solid-state potentiometer
2. The flexibility of computer-based digital controls
3. The retentivity of nonvolatile memory used for the storage
of multiple potentiometer settings or data
Mode Selection
CS
INC
U/D
MODE
L
H
Wiper Up
L
Wiper Down
H
X
Store Wiper Position
H
X
Standby Current
L
X
No Store, Return to Standby
L
H
Wiper Up (not recommended)
L
Wiper Down (not recommended)
WAVEFORM
INPUTS
OUTPUTS
Must be
steady
Will be
steady
May change
from Low to
High
Will change
from Low to
High
May change
from High to
Low
Will change
from High to
Low
Don’t Care:
Changes
Allowed
Changing:
State Not
Known
N/A
Center Line
is High
Impedance
X93254
相關PDF資料 |
PDF描述 |
|---|---|
| X93255UV14IT1 | IC XDCP DUAL 32-TAP 50K 14-TSSOP |
| X93256WV14I-2.7T1 | IC XDCP DUAL 32TAP 12.5K 14TSSOP |
| X9400YV24T1 | IC XDCP QUAD 64-TAP 2.5K 24TSSOP |
| X9401YV24I-2.7 | IC XDCP QUAD 64-TAP 2.5K 24TSSOP |
| X9408YV24T1 | IC XDCP QUAD 64-TAP 2.5K 24TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X93255 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual Digitally Controlled Potentiometers(XDCPs?) |
| X93255_08 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual Digitally Controlled Potentiometers(XDCPs?) |
| X93255UV14I | 功能描述:IC DCP DUAL 50K 32TAP 14-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X93255UV14IT1 | 功能描述:IC XDCP DUAL 32-TAP 50K 14-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| X93256 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual Digitally Controlled Potentiometers(XDCPs?) |
發布緊急采購，3分鐘左右您將得到回復。