參數資料
型號: X9409YS24
廠商: Intersil
文件頁數: 15/20頁
文件大?。?/td> 0K
描述: IC XDCP QUAD 64-TAP 2.5K 24-SOIC
標準包裝: 30
系列: XDCP™
接片: 64
電阻(歐姆): 2.5k
電路數: 4
溫度系數: 標準值 ±300 ppm/°C
存儲器類型: 非易失
接口: I²C(設備位址)
電源電壓: 4.5 V ~ 5.5 V
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 24-SOIC(0.295",7.50mm 寬)
供應商設備封裝: 24-SOIC
包裝: 管件
4
FN8192.4
October 12, 2006
controlled by the Wiper Counter Register (WCR). The
six bits of the WCR are decoded to select, and enable,
one of sixty-four switches.
The WCR may be written directly, or it can be changed
by transferring the contents of one of four associated
Data Registers into the WCR. These Data Registers
and the WCR can be read and written by the host
system.
Device Addressing
Following a start condition the master must output the
address of the slave it is accessing. The most
significant four bits of the slave address are the device
type identifier (refer to Figure 1 below). For the X9409
this is fixed as 0101[B].
Figure 1. Slave Address
The next four bits of the slave address are the device
address. The physical device address is defined by
the state of the A0 - A3 inputs. The X9409 compares
the serial data stream with the address input state; a
successful compare of all four address bits is required
for the X9409 to respond with an acknowledge. The
A0 - A3 inputs can be actively driven by CMOS input
signals or tied to VCC or VSS.
Acknowledge Polling
The disabling of the inputs, during the internal
nonvolatile write operation, can be used to take
advantage of the typical nonvolatile write cycle time.
Once the stop condition is issued to indicate the end of
the nonvolatile write command the X9409 initiates the
internal write cycle. ACK polling can be initiated
immediately. This involves issuing the start condition
followed by the device slave address. If the X9409 is
still busy with the write operation no ACK will be
returned. If the X9409 has completed the write
operation an ACK will be returned and the master can
then proceed with the next operation.
Flow 1. ACK Polling Sequence
Instruction Structure
The next byte sent to the X9409 contains the
instruction and register pointer information. The format
is shown in Figure 2.
Figure 2. Instruction Byte Format
The four high order bits define the instruction. The
next two bits (R1 and R0) select one of the four
registers that is to be acted upon when a register
oriented instruction is issued. The last bits (P1, P0)
select which one of the four potentiometers is to be
affected by the instruction.
1
00
A3
A2
A1
A0
Device Type
Identifier
Device Address
1
Nonvolatile Write
Command Completed
Enter ACK Polling
Issue
START
Issue Slave
Address
ACK
Returned?
Further
Operation?
Issue
Instruction
Issue STOP
NO
YES
Proceed
Issue STOP
NO
Proceed
I1
I2
I3
I0
R1
R0
P1
P0
Pot Select
Register
Select
Instructions
X9409
相關PDF資料
PDF描述
VE-BTF-MV-S CONVERTER MOD DC/DC 72V 150W
D38999/26JE8HN CONN PLUG 8POS STRAIGHT W/PINS
MS27508E24F35SD CONN RCPT 128POS BOX MNT W/SCKT
MS27508E24A35SC CONN RCPT 128POS BOX MNT W/SCKT
MS27484T20F2SA CONN PLUG 65POS STRAIGHT W/SCKT
相關代理商/技術參數
參數描述
X9409YS24-2.7 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Quad Digitally Controlled Potentiometers
X9409YS24I 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Quad Digitally Controlled Potentiometers
X9409YS24I-2.7 功能描述:IC XDCP QUAD 64-TAP 2.5K 24-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻(歐姆):50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行(芯片選擇,遞增,增/減) 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型,TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR)
X9409YS24IZ-2.7 功能描述:IC XDCP QUAD 64-TAP 2.5K 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻(歐姆):100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行(芯片選擇,遞增,增/減) 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR)
X9409YS24Z 功能描述:IC XDCP QUAD 64-TAP 2.5K 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻(歐姆):100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行(芯片選擇,遞增,增/減) 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR)