- 您現在的位置：買賣IC網 > PDF目錄9192 > X9409YV24IZ-2.7 (Intersil)IC XDCP QUAD 64-TAP 2.5K 24TSSOP PDF資料下載
參數資料
| 型號： | X9409YV24IZ-2.7 |
| 廠商： | Intersil |
| 文件頁數： | 4/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC XDCP QUAD 64-TAP 2.5K 24TSSOP |
| 標準包裝： | 62 |
| 系列： | XDCP™ |
| 接片： | 64 |
| 電阻（歐姆）： | 2.5k |
| 電路數： | 4 |
| 溫度系數： | 標準值 ±300 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 24-TSSOP |
| 包裝： | 管件 |
12
FN8192.4
October 12, 2006
D.C. OPERATING CHARACTERISTICS
(Over the recommended operating conditions unless otherwise specified.)
ENDURANCE AND DATA RETENTION
CAPACITANCE
POWER-UP TIMING
POWER-UP REQUIREMENTS (Power-up sequencing can affect correct recall of the wiper registers)
The preferred power-on sequence is as follows: First VCC, then the potentiometer pins, RH, RL, and RW. The VCC
ramp rate specification should be met, and any glitches or slope changes in the VCC line should be held to <100mV if
possible. If VCC powers down, it should be held below 0.1V for more than 1 second before powering up again in order
for proper wiper register recall. Also, VCC should not reverse polarity by more than 0.5V. Recall of wiper position will
not be complete until VCC reaches its final value.
Notes: (4) This parameter is periodically sampled and not 100% tested
(5) tPUR and tPUW are the delays required from the time the (last) power supply (VCC) is stable until the specific instruction can be issued.
These parameters are periodically sampled and not 100% tested.
(6) Sample tested only.
Symbol
Parameter
Limits
Test Conditions
Min.
Typ.
Max.
Unit
ICC1
VCC supply current (Active)
100
A
fSCL = 400kHz, SDA = Open,
Other Inputs = VSS
ICC2
VCC supply current
(Nonvolatile Write)
1mA
fSCL = 400kHz, SDA = Open,
Other Inputs = VSS
ISB
VCC current (standby)
1
A
SCL = SDA = VCC, Addr. = VSS
ILI
Input leakage current
10
A
VIN = VSS to VCC
ILO
Output leakage current
10
A
VOUT = VSS to VCC
VIH
Input HIGH voltage
VCC x 0.7
VCC + 0.5
V
VIL
Input LOW voltage
-0.5
VCC x 0.1
V
VOL
Output LOW voltage
0.4
V
IOL = 3mA
Parameter
Min.
Unit
Minimum endurance
100,000
Data changes per bit per register
Data retention
100
Years
Symbol
Test
Max.
Unit
Test Conditions
CI/O(4)
Input/output capacitance (SDA)
8
pF
VI/O = 0V
CIN(4)
Input capacitance (A0, A1, A2, A3, and SCL)
6
pF
VIN = 0V
Symbol
Parameter
Min.
Max.
Unit
tr VCC(6)
VCC power-up rate
0.2
50
V/ms
X9409
相關PDF資料 |
PDF描述 |
|---|---|
| VI-2WZ-MW-F3 | CONVERTER MOD DC/DC 2V 40W |
| IDT72V8980PV8 | IC DGTL SW 256X256 48-SSOP |
| X9408WV24IZ-2.7 | IC XDCP QUAD 64-TAP 10K 24-TSSOP |
| ICS843001AGLF | IC CLK GEN FIBRE LVPECL 8-TSSOP |
| V24A48H300B2 | CONVERTER MOD DC/DC 48V 300W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9409YZ24 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Quad Digitally Controlled Potentiometers |
| X9409YZ24-2.7 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Quad Digitally Controlled Potentiometers |
| X9409YZ24I | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Quad Digitally Controlled Potentiometers |
| X9409YZ24I-2.7 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Quad Digitally Controlled Potentiometers |
| X9410 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Noise/Low Power/SPI Bus |
發布緊急采購，3分鐘左右您將得到回復。