- 您現在的位置：買賣IC網 > PDF目錄371303 > X9448YS24 (INTERSIL CORP) Mixed Signal with 2-Wire Interface PDF資料下載
參數資料
| 型號： | X9448YS24 |
| 廠商： | INTERSIL CORP |
| 元件分類： | 數字電位計 |
| 英文描述： | Mixed Signal with 2-Wire Interface |
| 中文描述： | 2.5K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO24 |
| 封裝： | PLASTIC, SOIC-24 |
| 文件頁數： | 3/20頁 |
| 文件大?。?/td> | 127K |
| 代理商： | X9448YS24 |
X9448
Characteristics subject to change without notice.
3 of 20
REV 1.0 6/21/00
www.xicor.com
PIN NAMES
PRINCIPLES OF OPERATION
The X9448 is a highly integrated microcircuit incorpo-
rating two resistor arrays, two voltage comparators
and their associated registers and counters; and the
serial interface logic providing direct communication
between the host and the digitally-controlled potenti-
ometers and voltage comparators.
Serial Interface
The X9448 supports a bidirectional bus oriented proto-
col. The protocol defines any device that sends data
onto the bus as a transmitter and the receiving device
as the receiver. The device controlling the transfer is a
master and the device being controlled is the slave.
The master will always initiate data transfers and pro-
vide the clock for both transmit and receive operations.
Therefore, the X9448 will be considered a slave device
in all applications.
Clock and Data Conventions
Data states on the SDA line can change only during
SCL LOW periods (t
LOW
). SDA state changes during
SCL HIGH are reserved for indicating start and stop
conditions.
Start Condition
All commands to the X9448 are preceded by the start
condition, which is a HIGH to LOW transition of SDA
while SCL is HIGH (t
HIGH
). The X9448 continuously
monitors the SDA and SCL lines for the start condition
and will not respond to any command until this condi-
tion is met.
Stop Condition
All communications must be terminated by a stop con-
dition, which is a LOW to HIGH transition of SDA while
SCL is HIGH.
Acknowledge
Acknowledge is a software convention used to provide
a positive handshake between the master and slave
devices on the bus to indicate the successful receipt of
data. The transmitting device, either the master or the
slave, will release the SDA bus after transmitting eight
bits. The master generates a ninth clock cycle and dur-
ing this period the receiver pulls the SDA line LOW to
acknowledge that it successfully received the eight bits
of data.
The X9448 will respond with an acknowledge after
recognition of a start condition and its slave address
and once again after successful receipt of the com-
mand byte. If the command is followed by a data byte
the X9448 will respond with a final acknowledge.
Array Description
The X9448 is comprised of two resistor arrays and two
voltage comparators. Each array contains 63 discrete
resistive segments that are connected in series. The
physical ends of each array are equivalent to the fixed
terminals of a mechanical potentiometer (V
inputs).
H
and V
L
At both ends of each array and between each resistor
segment is a CMOS switch connected to the wiper
(V
W
) output. Within each individual array only one
switch may be turned on at a time. These switches are
controlled by a volatile wiper counter register (WCR).
The six bits of the WCR are decoded to select, and
enable, one of sixty-four switches.
The WCR may be written directly, or it can be changed
by transferring the contents of one of four associated
data registers into the WCR. These data registers and
the WCR can be read and written by the host system.
Symbol
SCL
SDA
A0-A3
V
H0
–V
V
L0
–V
V
W0
–V
V
NI0
, V
V
OUT0,
WP
V+,V-
Description
Serial Clock
Serial Data
Device Address
Potentiometers (terminal equivalent)
H1
L1
,
W1
Potentiometers (wiper equivalent)
Comparator Input Voltages
Buffered Comparator Outputs
Hardware Write Protection
Analog and Voltage Comparator
Supplies
System/Digital Supply Voltage
System Ground
No Connection
NI1
V
OUT1
V
V
NC
CC
SS
相關PDF資料 |
PDF描述 |
|---|---|
| X9448YP24I-2.7 | VGA VIDEO CABLE 100 FT FF |
| X9448YP24 | VGA VIDEO CABLE 20 FT MM |
| X9448YP24-2.7 | VGA VIDEO CABLE 35 FT FF |
| X9448YP24I | VGA VIDEO CABLE 50 FT MF |
| X9448WP24I | FILTER SAW 315.15MHZ REMOTE SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9448YS24-2.7 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Mixed Signal with 2-Wire Interface |
| X9448YS24I | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Mixed Signal with 2-Wire Interface |
| X9448YS24I-2.7 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Mixed Signal with 2-Wire Interface |
| X9448YV24 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Mixed Signal with 2-Wire Interface |
| X9448YV24-2.7 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Mixed Signal with 2-Wire Interface |
發布緊急采購，3分鐘左右您將得到回復。