- 您現在的位置：買賣IC網 > PDF目錄376448 > X9520V20IA (Intersil Corporation) Triple DCP, POR,2kbit EEPROM Memory, Dual Voltage Monitors PDF資料下載
參數資料
| 型號： | X9520V20IA |
| 廠商： | Intersil Corporation |
| 英文描述： | Triple DCP, POR,2kbit EEPROM Memory, Dual Voltage Monitors |
| 中文描述： | 三氯酚，葡萄牙，2kbit EEPROM存儲器，雙電壓監視器 |
| 文件頁數： | 7/33頁 |
| 文件大?。?/td> | 561K |
| 代理商： | X9520V20IA |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
7
FN8206.0
March 8, 2005
The data in the WCR is then decoded to select and
enable one of the respective FET switches. A “make
before break” sequence is used internally for the FET
switches when the wiper is moved from one tap position
to another.
Hot Pluggability
Figure 7 shows a typical waveform that the X9520 might
experience in a Hot Pluggable situation. On power-up,
V1 / Vcc applied to the X9520 may exhibit some amount
of ringing, before it settles to the required value.
The device is designed such that the wiper terminal
(R
Wx
) is recalled to the correct position (as per the last
stored in the DCP NVM), when the voltage applied to V1
/ Vcc exceeds V
TRIP1
for a time exceeding t
purst
(the
Power-on Reset time, set in the CONSTAT Register -
See “CONTROL AND STATUS REGISTER” on
page 13.).
Therefore, if
t
trans
is defined as the time taken for V1 /
Vcc to settle above V
TRIP1
(Figure 7): then the desired
wiper terminal position is recalled by (a maximum) time:
t
trans
+
t
purst
. It should be noted that
t
trans
is deter-
mined by system hot plug conditions.
DCP Operations
In total there are three operations that can be performed
on any internal DCP structure:
—DCP Nonvolatile Write
—DCP Volatile Write
—DCP Read
A nonvolatile write to a DCP will change the “wiper
position” by simultaneously writing new data to the
associated WCR and NVM. Therefore, the new “wiper
position” setting is recalled into the WCR after V1 / Vcc of
the X9520 is powered down and then powered back up.
A volatile write operation to a DCP however, changes the
“wiper position” by writing new data to the associated
WCR only. The contents of the associated NVM register
remains unchanged. Therefore, when V1 / Vcc to the
device is powered down then back up, the “wiper
position” reverts to that last position written to the DCP
using a nonvolatile write operation.
Both volatile and nonvolatile write operations are
executed using a three byte command sequence: (DCP)
Slave Address Byte, Instruction Byte, followed by a Data
Byte (See Figure 9)
A DCP Read operation allows the user to “read out” the
current “wiper position” of the DCP, as stored in the
associated WCR. This operation is executed using the
Random Address Read command sequence, consisting
of the (DCP) Slave Address Byte followed by an
Instruction Byte and the Slave Address Byte again (Refer
to Figure 10.).
Instruction Byte
While the Slave Address Byte is used to select the DCP
devices, an Instruction Byte is used to determine which
DCP is being addressed.
The Instruction Byte (Figure 8) is valid only when the
Device Type Identifier and the Internal Device Address
bits of the Slave Address are set to 1010111. In this
case, the two Least Significant Bit’s (I1 - I0) of the
Instruction Byte are used to select the particular DCP (0
- 2). In the case of a Write to any of the DCPs (i.e. the
LSB of the Slave Address is 0), the Most Significant Bit of
the Instruction Byte (I7), determines the Write Type (WT)
performed.
If WT is “1”, then a Nonvolatile Write to the DCP
occurs.
In this case, the “wiper position” of the DCP is changed
by simultaneously writing new data to the associated
Figure 7.
DCP Power
t
V1 / Vcc
V
TRIP1
V1 / Vcc (Max.)
t
purst
Maximum Wiper Recall time
0
t
trans
X9520
相關PDF資料 |
PDF描述 |
|---|---|
| X9520V20IB | Triple DCP, POR,2kbit EEPROM Memory, Dual Voltage Monitors |
| X9522 | Laser Diode Control for Fiber Optic Modules |
| X9522B20I-A | Laser Diode Control for Fiber Optic Modules |
| X9522B20I-B | Laser Diode Control for Fiber Optic Modules |
| X9522V20I-A | Laser Diode Control for Fiber Optic Modules |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9520V20I-A | 功能描述:IC 3 DCP 2K EE LASR CTRL 20TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9520V20I-AT1 | 功能描述:IC VOLT MON DUAL 2KBIT 20-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9520V20I-AT2 | 功能描述:IC VOLT MON DUAL 2KBIT 20-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9520V20IB | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple DCP, POR,2kbit EEPROM Memory, Dual Voltage Monitors |
| X9520V20I-B | 功能描述:IC 3 DCP 2K EE LASR CTRL 20TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
發布緊急采購，3分鐘左右您將得到回復。