- 您現在的位置：買賣IC網 > PDF目錄376448 > X9520V20IB (Intersil Corporation) Triple DCP, POR,2kbit EEPROM Memory, Dual Voltage Monitors PDF資料下載
參數資料
| 型號： | X9520V20IB |
| 廠商： | Intersil Corporation |
| 英文描述： | Triple DCP, POR,2kbit EEPROM Memory, Dual Voltage Monitors |
| 中文描述： | 三氯酚，葡萄牙，2kbit EEPROM存儲器，雙電壓監視器 |
| 文件頁數： | 15/33頁 |
| 文件大?。?/td> | 561K |
| 代理商： | X9520V20IB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
15
FN8206.0
March 8, 2005
CONSTAT Register Write Operation
The CONSTAT register is accessed using the Slave
Address set to 1010010 (Refer to Figure 4.). Following
the Slave Address Byte, access to the CONSTAT regis-
ter requires an Address Byte which must be set to FFh.
Only one data byte is allowed to be written for each
CONSTAT register Write operation. The user must issue
a STOP, after sending this byte to the register, to initiate
the nonvolatile cycle that stores the BP1, BP0, POR1
and POR0 bits. The X9520 will not ACKNOWLEDGE
any data bytes written after the first byte is entered (Refer
to Figure 18.).
Prior to writing to the CONSTAT register, the WEL and
RWEL bits must be set using a two step process, with
the whole sequence requiring 3 steps
—Write a 02H to the CONSTAT Register to set the Write
Enable Latch (WEL). This is a volatile operation, so
there is no delay after the write. (Operation preceded
by a START and ended with a STOP).
—Write a 06H to the CONSTAT Register to set the Reg-
ister Write Enable Latch (RWEL) AND the WEL bit.
This is also a volatile cycle. The zeros in the data byte
are required. (Operation preceded by a START and
ended with a STOP).
—Write a one byte value to the CONSTAT Register that
has all the bits set to the desired state. The CONSTAT
register can be represented as qxyst01r in binary,
where xy are the Voltage Monitor Output Status
(V2OS and V3OS) bits, st are the Block Lock Protec-
tion (BL1 and BL0) bits, and qr are the Power-on Reset
delay time (t
PUV1RO
) control bits (POR1 - POR0).
This operation is proceeded by a START and ended
with a STOP bit. Since this is a nonvolatile write cycle,
it will typically take 5ms to complete. The RWEL bit is
reset by this cycle and the sequence must be repeated
to change the nonvolatile bits again. If bit 2 is set to ‘1’
in this third step (qxys t11r) then the RWEL bit is set,
but the V2OS, V3OS, POR1, POR0, BL1 and BL0 bits
remain unchanged. Writing a second byte to the con-
trol register is not allowed. Doing so aborts the write
operation and the X9520 does not return an
ACKNOWLEDGE.
For example, a sequence of writes to the device CON-
STAT register consisting of [02H, 06H, 02H] will reset all
of the nonvolatile bits in the CONSTAT Register to “0”.
It should be noted that a write to any nonvolatile bit of
CONSTAT register will be ignored if the Write Protect
pin of the X9520 is active (HIGH) (See "WP: Write Pro-
tection Pin").
CONSTAT Register Read Operation
The contents of the CONSTAT Register can be read at
any time by performing a random read (See Figure 19).
Using the Slave Address Byte set to 10100101, and an
Address Byte of FFh. Only one byte is read by each reg-
ister read operation. The X9520 resets itself after the first
byte is read. The master should supply a STOP condition
to be consistent with the bus protocol.
After setting the WEL and / or the RWEL bit(s) to a “1”,
a CONSTAT register read operation may occur, without
interrupting a proceeding CONSTAT register write
operation.
0
Slave
Address
Address
Byte
A
C
K
A
C
K
S
t
a
r
t
S
t
o
p
Slave
Address
Data
A
C
K
1
S
t
a
r
t
SDA Bus
Signals from
the Slave
Signals from
the Master
Figure 19. CONSTAT Register Read Command Sequence
0 1 0 0 1 0
1
1
0 1 0 0 1 0
WRITE Operation
“Dummy” Write
READ Operation
CS7 … CS0
X9520
相關PDF資料 |
PDF描述 |
|---|---|
| X9522 | Laser Diode Control for Fiber Optic Modules |
| X9522B20I-A | Laser Diode Control for Fiber Optic Modules |
| X9522B20I-B | Laser Diode Control for Fiber Optic Modules |
| X9522V20I-A | Laser Diode Control for Fiber Optic Modules |
| X9522V20I-B | Laser Diode Control for Fiber Optic Modules |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9520V20I-B | 功能描述:IC 3 DCP 2K EE LASR CTRL 20TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9520V20I-BT1 | 功能描述:IC VOLT MON DUAL 2KBIT 20-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9520V20IZ-A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple DCP, POR, 2kbit EEPROM Memory, Dual Voltage Monitors |
| X9520V20IZ-AT1 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple DCP, POR, 2kbit EEPROM Memory, Dual Voltage Monitors |
| X9520V20IZ-AT2 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple DCP, POR, 2kbit EEPROM Memory, Dual Voltage Monitors |
發布緊急采購，3分鐘左右您將得到回復。