- 您現在的位置：買賣IC網 > PDF目錄376449 > X9525B20I (INTERSIL CORP) Fiber Channel/Gigabit Etherner Laser Diode Control for Fiber Optic Modules PDF資料下載
參數資料
| 型號： | X9525B20I |
| 廠商： | INTERSIL CORP |
| 元件分類： | 數字電位計 |
| 英文描述： | Fiber Channel/Gigabit Etherner Laser Diode Control for Fiber Optic Modules |
| 中文描述： | DUAL 50K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, BGA20 |
| 封裝： | CSP-20 |
| 文件頁數： | 10/26頁 |
| 文件大小： | 578K |
| 代理商： | X9525B20I |
10
FN8210.0
March 10, 2005
Stops and EEPROM Write Modes
Stop conditions that terminate write operations must be
sent by the master after sending at least 1 full data byte
and receiving the subsequent ACKNOWLEDGE signal.
If the master issues a STOP within a Data Byte, or before
the X9525 issues a corresponding ACKNOWLEDGE,
the X9525 cancels the write operation. Therefore, the
contents of the EEPROM array does not change.
EEPROM Array Read Operations
Read operations are initiated in the same manner as
write operations with the exception that the R/W bit of the
Slave Address Byte is set to one. There are three basic
read operations: Current EEPROM Address Read, Ran-
dom EEPROM Read, and Sequential EEPROM Read.
Current EEPROM Address Read
Internally the device contains an address counter that
maintains the address of the last word read incre-
mented by one. Therefore, if the last read was to
address n, the next read operation would access data
from address n + 1. On power-up, the address of the
address counter is undefined, requiring a read or write
operation for initialization.
Upon receipt of the Slave Address Byte with the R/W bit
set to one, the device issues an ACKNOWLEDGE and
then transmits the eight bits of the Data Byte. The master
terminates the read operation when it does not respond
with an ACKNOWLEDGE during the ninth clock and then
issues a STOP condition (See Figure 14 for the address,
ACKNOWLEDGE, and data transfer sequence).
It should be noted that the ninth clock cycle of the read
operation is not a “don’t care.” To terminate a read oper-
ation, the master must either issue a STOP condition
during the ninth cycle or hold SDA HIGH during the ninth
clock cycle and then issue a STOP condition.
Another important point to note regarding the “Current
EEPROM Address Read” , is that this operation is not
available if the last executed operation was an access to
a DCP or the CONSTAT Register (i.e.: an operation
using the Device Type Identifier 1010A
0
11 or
1010A
0
10). Immediately after an operation to a DCP or
CONSTAT Register is performed, only a “Random
EEPROM Read” is available. Immediately following a
“Random EEPROM Read” , a “Current EEPROM
Address Read” or “Sequential EEPROM Read” is once
again available (assuming that no access to a DCP or
CONSTAT Register occur in the interim).
address
15
address
11
5 bytes
7 bytes
address
= 6
address pointer
ends here
Addr = 7
Figure 13. Example: Writing 2 bytes to a 16-byte page starting at location 11.
10
10
10
10
S
t
a
r
t
S
t
o
p
Slave
Address
Data
A
C
K
SDA Bus
Signals from
the Slave
Signals from
the Master
1
Figure 14. Current EEPROM Address Read Sequence
1
0
0 0
A
0
1
0
X9525
相關PDF資料 |
PDF描述 |
|---|---|
| X9525 | Fiber Channel/Gigabit Etherner Laser Diode Control for Fiber Optic Modules |
| X9525V20I | Fiber Channel/Gigabit Etherner Laser Diode Control for Fiber Optic Modules |
| X9530 | Temperature Compensated Laser Diode Controller(帶溫度補償的激光二極管控制器) |
| X95840 | Quad Digital Controlled Potentiometers |
| X95840WV20I-2.7 | Quad Digital Controlled Potentiometers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9525BZ WAF | 制造商:Intersil Corporation 功能描述: |
| X9525V20I | 功能描述:IC DCP DUAL EEPROM MEM 20-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9525V20IT1 | 功能描述:IC DCP DUAL EEPROM MEM 20-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9525V20IZ | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual DCP, EEPROM Memory |
| X9530 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Temperature Compensated Laser Diode Controller |
發(fā)布緊急采購，3分鐘左右您將得到回復。