參數資料
型號： X98024
廠商： Intersil Corporation
英文描述： 240MHz Triple Video Digitizer with Digital PLL
中文描述： 240MHz的三路視頻數字化與數字鎖相環
文件頁數： 25/29頁
文件大?。?/td> 295K
代理商： X98024
25
FN8220.0
June 6, 2005
This is a rarely used composite sync format; in most
applications it will never be encountered. However if this
CSYNC waveform must be supported, there is a simple
applications solution using an XOR gate.
The output of the XOR gate is connected to the HSYNC
IN
input of the X98024. One of the XOR inputs is connected to
the HSYNC/CSYNC source, and the other input is
connected to a general purpose I/O. For all sync sources
except the CSYNC shown in Figure 11, the input connected
to the GPIO should be driven low.
If the system microcontroller detects a mode corresponding
to the sync type and polarity shown in Figure 11, it should
drive the GPIO pin high. This will invert the CSYNC signal
seen by the X98024 and prevent any spontaneous image
shifting.
X98024 Serial Communication
Overview
The X98024 uses a 2 wire serial bus for communication with
its host. SCL is the Serial Clock line, driven by the host, and
SDA is the Serial Data line, which can be driven by all
devices on the bus. SDA is open drain to allow multiple
devices to share the same bus simultaneously.
Communication is accomplished in three steps:
1. The Host selects the X98024 it wishes to communicate
with.
2. The Host writes the initial X98024 Configuration Register
address it wishes to write to or read from.
3. The Host writes to or reads from the X98024’s
Configuration Register. The X98024’s internal address
pointer auto increments, so to read registers 0x00
through 0x1B, for example, one would write 0x00 in step
2, then repeat step 3 28 times, with each read returning
the next register value.
The X98024 has a 7 bit address on the serial bus. The upper
6 bits are permanently set to 100110, with the lower bit
determined by the state of pin 48. This allows 2 X98024s to
be independently controlled while sharing the same bus.
The bus is nominally inactive, with SDA and SCL high.
Communication begins when the host issues a START
command by taking SDA low while SCL is high (Figure 12).
The X98024 continuously monitors the SDA and SCL lines
for the start condition and will not respond to any command
until this condition has been met. The host then transmits the
7 bit serial address plus a R/W bit, indicating if the next
transaction will be a Read (R/W = 1) or a Write (R/W = 0). If
the address transmitted matches that of any device on the
bus, that device must respond with an ACKNOWLEDGE
(Figure 13).
Once the serial address has been transmitted and
acknowledged, one or more bytes of information can be
written to or read from the slave. Communication with the
selected device in the selected direction (read or write) is
ended by a STOP command, where SDA rises while SCL is
high (Figure 12), or a second START command, which is
commonly used to reverse data direction without
relinquishing the bus.
Data on the serial bus must be valid for the entire time SCL
is high (Figure 14). To achieve this, data being written to the
X98024 is latched on a delayed version of the rising edge of
SCL. SCL is delayed and deglitched inside the X98024 for 3
crystal clock periods (120ns for a 25MHz crystal) to eliminate
spurious clock pulses that could disrupt serial
communication.
When the contents of the X98024 are being read, the SDA
line is updated after the falling edge of SCL, delayed and
deglitched in the same manner.
Configuration Register Write
Figure 15 shows two views of the steps necessary to write
one or more words to the Configuration Register.
Configuration Register Read
Figure 16 shows two views of the steps necessary to read
one or more words from the Configuration Register.
FIGURE 11. CSYNC ON HSYNC THAT MAY CAUSE SPORADIC IMAGE SHIFTS
t
1
t
2
HSYNC
IN
Conditions required: negative polarity VSYNC, with no serrations, and t
1
= t
2
X98024
相關PDF資料
PDF描述
X98024L128-3.3 240MHz Triple Video Digitizer with Digital PLL
X98024L128-3.3-Z 240MHz Triple Video Digitizer with Digital PLL
XC145481 3 V PCM Codec-Filter
XC145481DW 3 V PCM Codec-Filter
XC145481P 3 V PCM Codec-Filter
相關代理商/技術參數
參數描述
X98024_06 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:240MHz Triple Video Digitizer with Digital PLL
X98024L128-3.3 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:240MHz Triple Video Digitizer with Digital PLL
X98024L128-3.3-Z 功能描述:IC TRPL VID DIGITIZER 128MQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 標準包裝:250 系列:- 類型:電平移位器 應用:LCD 電視機/監控器 安裝類型:表面貼裝 封裝/外殼:28-WFQFN 裸露焊盤 供應商設備封裝:28-WQFN（4x4）裸露焊盤 包裝:帶卷 (TR) 其它名稱:296-32523-2TPS65198RUYT-ND
X98027 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:PRELIMINARY INFORMATION
X98027_06 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:275MHz Triple Video Digitizer with Digital PLL
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*