參數資料
型號: XC2C384-7FGG324C
廠商: Xilinx Inc
文件頁數: 16/16頁
文件大小: 0K
描述: IC CR-II CPLD 384MCELL 324-FBGA
標準包裝: 60
系列: CoolRunner II
可編程類型: 系統內可編程
最大延遲時間 tpd(1): 7.1ns
電壓電源 - 內部: 1.7 V ~ 1.9 V
邏輯元件/邏輯塊數目: 24
宏單元數: 384
門數: 9000
輸入/輸出數: 240
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 324-BBGA
供應商設備封裝: 324-FBGA(23x23)
包裝: 托盤
CoolRunner-II CPLD Family
DS090 (v3.1) September 11, 2008
Product Specification
R
Additional Clock Options: Division,
DualEDGE, and CoolCLOCK
Clock Divider
A
clock
divider
circuit
has
been
included
in
the
CoolRunner-II CPLD architecture to divide one externally
supplied global clock by standard values. The allowable val-
ues for the division are 2, 4, 6, 8, 10, 12, 14, and 16 (see
Figure 8). This capability is supplied on the GCK2 pin. The
resulting clock produced has a 50% duty cycle for all possi-
ble divisions. The output of the clock divider is on global
routing. If the clock divider is used, the undivided clock is
available internally. If the undivided clock is required inter-
nally it is input through a separate clock pin.
The clock divider circuit encompasses a synchronous reset
(CDRST) to guarantee no spurious clocks can carry
through on to the global clock nets. When the CDRST signal
is asserted, the clock divider output is disabled after the cur-
rent cycle. When the CDRST signal is deasserted the clock
divider output becomes active upon the first edge of GCK2.
The CDRST pin functions as a reset pin regardless of which
CLK_DIV primitive is used. If a clock divider is used in the
design, the CDRST pin is reserved and if it is driven High
the clock divider is reset. If a reset port of a clock divider is
not used, it is tied Low on the board. The clock divider circuit
includes an active High synchronous reset, referred to as
CDRST.
The CoolRunner-II CPLD clock divider includes a built-in
delay circuit. With the delay feature enabled, the output of
the clock divider is delayed for one full count cycle. When
used, the clock divider does not output a rising clock edge
until after the divider reaches the delay value. The delay fea-
ture is either enabled or disabled upon configuration.
Xilinx Synthesis Technology (XST) allows a clock divider
component to be instantiated directly in the HDL source
code. See XAPP378 for instantiation examples in VHDL,
Verilog, and ABEL.
DualEDGE
Each macrocell has the ability to double its input clock
switching frequency. Figure 9 shows the macrocell flip-flop
with the DualEDGE option (doubled clock) at each macro-
cell. The source to double can be a control term clock, a
product term clock or one of the available global clocks. The
ability to switch on both clock edges, also known as dual
edge triggered (DET), is vital for a number of synchronous
memory interface applications as well as certain double
data rate I/O applications.
CoolRunner-II CPLD DET registers can be used for logic
functions that include shift registers, counters, comparators,
and state machines. Designers must evaluate the desired
performance of the CPLD logic to determine use of DET
registers.
The DET register can be inferred in any ABEL, HDL, or
schematic design. A designer can infer a single-edge trig-
gered (SET) register in any HDL design. The DET register is
available with all macrocells in all devices of the
CoolRunner-II family.
CoolCLOCK
In addition to the DualEDGE flip-flop, power savings can
occur by combining the clock division circuitry with the
DualEDGE circuitry. This capability is called CoolCLOCK
and is designed to reduce clocking power within the CPLD.
Because the clock net can be an appreciable power drain,
the clock power can be reduced by driving the net at half fre-
quency, then doubling the clock rate using DualEDGE trig-
gering at the macrocells. Figure 10 shows how CoolCLOCK
is created by internal clock cascading with the divider and
DualEDGE flip-flop working together.
GCK2 is the only clock network that can be divided, the
CoolCLOCK feature is only available on GCK2. The Cool-
CLOCK feature can be implemented by assigning an
attribute to an input clock. The CoolCLOCK attribute
replaces the need to instantiate the clock divider and infer
DET registers. The CoolCLOCK feature is available on
CoolRunner-II 128 macrocell devices and larger. See
XAPP378 for more detail.
Figure 8: Clock Division Circuitry for GCK2
DS090_08_121201
Clock
In
÷2
÷4
÷6
÷8
÷10
÷12
÷14
÷16
GCK2
CDRST
相關PDF資料
PDF描述
TAJT106M016RNJ CAP TANT 10UF 16V 20% 1210
GCC08DCMN CONN EDGECARD 16POS .100" WW
XC2C512-10PQG208I IC CR-II CPLD 512MCRCELL 208PQFP
PQ1L333M2SP IC REG LDO 3.3V .3A SOT-89
TAJT106M010YNJ CAP TANT 10UF 10V 20% 1210
相關代理商/技術參數
參數描述
XC2C384-7FT256C 制造商:Xilinx 功能描述:CPLD COOLRUNNER-II 9K GATES 384 MCRCLLS 350MHZ 0.18UM 1.8V 2 - Trays 制造商:Xilinx 功能描述:IC CR-II CPLD 384MCELL 256-FBGA
XC2C384-7FTG256C 功能描述:IC CRII CPLD 384MCRCELL 256BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - CPLD(復雜可編程邏輯器件) 系列:CoolRunner II 標準包裝:40 系列:ispMACH® 4000C 可編程類型:系統內可編程 最大延遲時間 tpd(1):5.0ns 電壓電源 - 內部:1.65 V ~ 1.95 V 邏輯元件/邏輯塊數目:32 宏單元數:512 門數:- 輸入/輸出數:128 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:176-LQFP 供應商設備封裝:176-TQFP(24x24) 包裝:托盤
XC2C384-7PQ208C 制造商:Xilinx 功能描述:CPLD COOLRUNNER-II 9K GATES 384 MCRCLLS 350MHZ 0.18UM 1.8V 2 - Trays 制造商:Xilinx 功能描述:IC CPLD 384MC 7.1NS 208PQFP
XC2C384-7PQG208C 功能描述:IC CR-II CPLD 384MCELL 208-PQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - CPLD(復雜可編程邏輯器件) 系列:CoolRunner II 標準包裝:24 系列:CoolRunner II 可編程類型:系統內可編程 最大延遲時間 tpd(1):7.1ns 電壓電源 - 內部:1.7 V ~ 1.9 V 邏輯元件/邏輯塊數目:24 宏單元數:384 門數:9000 輸入/輸出數:173 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:208-BFQFP 供應商設備封裝:208-PQFP(28x28) 包裝:托盤
XC2C384-7TQ144C 制造商:Xilinx 功能描述:CPLD COOLRUNNER-II 9K GATES 384 MCRCLLS 350MHZ 0.18UM 1.8V 1 - Trays 制造商:Xilinx 功能描述:IC CR-II CPLD 384MCELL 144-TQFP 制造商:Xilinx 功能描述:IC CPLD 384MC 7.1NS 144TQFP