參數資料
型號: XE8805AMI028LF
廠商: Semtech
文件頁數: 121/156頁
文件大小: 0K
描述: IC DAS 16BIT FLASH 8K MTP 64LQFP
標準包裝: 160
系列: XE880x
應用: 感測機
核心處理器: Coolrisc816?
程序存儲器類型: 閃存(22 kB)
控制器系列: XE8000
RAM 容量: 512 x 8
接口: UART,USRT
輸入/輸出數: 24
電源電壓: 2.4 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 64-LQFP
包裝: 托盤
供應商設備封裝: 64-LQFP(10x10)
產品目錄頁面: 585 (CN2011-ZH PDF)
配用: XE8000MP-ND - PROG BOARD AND PROSTART2 CARD
Semtech 2006
www.semtech.com
12-3
XE8805/05A
Note: Depending on the status of the EnResPConf bit in RegSysCtrl, the reset conditions of the registers are
different. See the reset block documentation for more details on the resetpconf signal.
12.4 Port B capabilities
Port B
usage (priority)
name
analog
(high)
functions
(medium)
digital
(low) (default)
PB[7]
uart Rx
I/O
PB[6]
analog
uart Tx
I/O
PB[5]
usrt S1
I/O
PB[4]
analog
usrt S0
I/O
PB[3]
32 kHz
I/O
PB[2]
analog
clock CPU
I/O
PB[1]
PWM1 Counter C (C+D)
I/O
PB[0]
analog
PWM0 Counter A (A+B)
I/O
Table 12-7: Different Port B functionality
Table 12-7 shows the different usage that can be made of the port B with the order of priority. If a pair of pins is
selected to be analog, it overwrites the function and digital set-up. If the pin is not selected as analog, but a
function is enabled, it overwrites the digital set-up. If neither the analog nor function are selected for a pin, it is used
as an ordinary digital I/O. This is the default configuration at start-up.
12.5 Port B analog capability
12.5.1
Port B analog configuration
Port B terminals can be attached to a 4 line analog bus by setting the PBAna[x] bits to 1 in the RegPBAna
register.
The other registers then define the connection of these 4 analog lines to the different pads of Port B. This can be
used to implement a simple LCD driver or A/D converter. Analog switching is available only when the circuit is
powered with sufficient voltage (see specification below). Below the specified supply voltage, only voltages that are
close to VSS or VBAT can be switched.
When PBAna[x] is set to 1, a pair of Port B terminals is switched from digital I/O mode to analog mode. The usage
of the registers RegPBPullup, RegPBOut and RegPBDir define the analog configuration (see Table 12-8).
When PBAna[x] = 1, then PBPullup[x] connects the pin to the analog bus. PBDir[x] and PBPOut[x] select which
of the 4 analog lines is used. For odd values of x, the selection bits are in the register RegPBOut (see Table 12-8).
For even values of x, the selection bits are in the register RegPBDir (see Table 12-9).
if x is odd, PBOut[x, x-1]
PBPullup[x]
PB[x] selection on
00
1
analog line 0
01
1
analog line 1
10
1
analog line 2
11
1
analog line 3
XX
0
High impedance
Table 12-8: Selection of the analog lines for PB[x] when x is odd and PBAna[x] = 1
Not
Recommended
for
New
Designs
相關PDF資料
PDF描述
XE8807AMI026TLF IC MCU LOW PWR MTP FLASH 32-TQFP
XIO2200AGGW IC PCI-EXPRESS/BUS BRIDGE 176BGA
XIO2200AZGW IC PCI-EXPRESS/BUS BRIDGE 176BGA
XPC823ZT81B2T IC MPU POWERQUICC 81MHZ 256-PBGA
XPC8240RZU250E MCU HOST PROCESSOR 352-TBGA
相關代理商/技術參數
參數描述
XE8805AMI028TLF 制造商:Semtech Corporation 功能描述:
XE8805MI028 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Data Acquisition MCU
XE8806A 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Ultra Low-Power Low-Voltage
XE8806AMI000 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Ultra Low-Power Low-Voltage
XE8806AMI026LF 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Ultra Low-Power Low-Voltage