- 您現在的位置：買賣IC網 > PDF目錄372930 > XQR1701LSERIES QPro Series Configuration PROMs (XQ) including Radiation-Hardened Series (XQR) PDF資料下載
參數資料
| 型號： | XQR1701LSERIES |
| 英文描述： | QPro Series Configuration PROMs (XQ) including Radiation-Hardened Series (XQR) |
| 中文描述： | QPro系列配置PROM的（學琴），包括抗輻射系列（XQR） |
| 文件頁數： | 3/17頁 |
| 文件大?。?/td> | 171K |
| 代理商： | XQR1701LSERIES |
QPro XQ18V04 (XQR18V04) QML In-System Programmable Configuration PROMs
DS082 (v1.2) November 5, 2001
Preliminary Product Specification
1-800-255-7778RCF
22
DATA OUT
Allows JTAG CONFIG instruction to initiate FPGA
configuration without powering down FPGA. This is an
open-drain output that is pulsed Low by the JTAG CONFIG
command.
10
16
21
OUTPUT
ENABLE
CEO
13
DATA OUT
Chip Enable Output (CEO) is connected to the CE input of
the next PROM in the chain. This output is Low when CE is
Low and OE/RESET input is High, AND the internal
address counter has been incremented beyond its
Terminal Count (TC) value. When OE/RESET goes Low,
CEO stays High until the PROM is brought out of reset by
bringing OE/RESET High.
21
27
14
OUTPUT
ENABLE
GND
GND is the ground connection.
6, 18,
28 &
41
3, 12,
24 &
34
TMS
MODE SELECT
The state of TMS on the rising edge of TCK determines the
state transitions at the Test Access Port (TAP) controller.
TMS has an internal 50K ohm resistive pull-up on it to
provide a logic "1" to the device if the pin is not driven.
5
11
TCK
CLOCK
This pin is the JTAG test clock. It sequences the TAP
controller and all the JTAG test and programming
electronics.
7
13
TDI
DATA IN
This pin is the serial input to all JTAG instruction and data
registers. TDI has an internal 50K ohm resistive pull-up on
it to provide a logic "1" to the system if the pin is not driven.
3
9
TDO
DATA OUT
This pin is the serial output for all JTAG instruction and data
registers. TDO has an internal 50K ohm resistive pull-up on
it to provide a logic "1" to the system if the pin is not driven.
31
37
V
CC
Positive 3.3V supply voltage for internal logic and input
buffers.
17, 35
& 38
23, 41
& 44
V
CCO
Positive 3.3V or 2.5V supply voltage connected to the
output voltage drivers.
8, 16,
26 &
36
14, 22,
32 &
42
Table 1:
Pin Names and Descriptions (pins not listed are
“
no connect
”
)
(Continued)
Pin
Name
Boundary
Scan
Order
Function
Pin Description
44-pin
VQFP
44-pin
CLCC
相關PDF資料 |
PDF描述 |
|---|---|
| XQ1701L-CC44B | Configuration EPROM |
| XQ1701L-CC44M | Configuration EPROM |
| XQ1701LSERIES | QPro Series Configuration PROMs (XQ) including Radiation-Hardened Series (XQR) |
| XQ1701L-SO20N | Configuration EPROM |
| XQR4000XL | QPRO XQR4000XL Radiation Hardened FPGAs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XQR1701LSO20M | 制造商:XILINX 制造商全稱:XILINX 功能描述:QPro Series Configuration PROMs (XQ) including Radiation-Hardened Series (XQR) |
| XQR1701LSO20N | 制造商:XILINX 制造商全稱:XILINX 功能描述:QPro Series Configuration PROMs (XQ) including Radiation-Hardened Series (XQR) |
| XQR1701LSO20V | 制造商:XILINX 制造商全稱:XILINX 功能描述:QPro Series Configuration PROMs (XQ) including Radiation-Hardened Series (XQR) |
| XQR18V04 | 制造商:XILINX 制造商全稱:XILINX 功能描述:QPro XQ18V04 (XQR18V04) QML In-System Programmable Configuration PROMs |
| XQS14+A2FZ | 制造商:Panasonic Industrial Company 功能描述:SCREW (1/10) |
發布緊急采購，3分鐘左右您將得到回復。