REV. 2.1.3 2.97V TO 5.5V DUAL UART WITH 128-BYTE FIFOS 3 PIN DESCRIPTIONS NAME 44-P" />
參數資料
型號： XR16C2850CM-F
廠商： Exar Corporation
文件頁數： 23/51頁
文件大?。?/td> 0K
描述： IC UART FIFO 128B DUAL 48TQFP
標準包裝： 250
特點： *
通道數： 2，DUART
FIFO's： 128 字節
規程： RS232，RS485
電源電壓： 2.97 V ~ 5.5 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 48-TQFP
供應商設備封裝： 48-TQFP（7x7）
包裝： 托盤
其它名稱： 1016-1274
xr
XR16C2850
REV. 2.1.3
2.97V TO 5.5V DUAL UART WITH 128-BYTE FIFOS
3
PIN DESCRIPTIONS
NAME
44-PLCC
PIN #
48-TQFP
PIN #
TYPE
DESCRIPTION
DATA BUS INTERFACE
A2
A1
A0
29
30
31
26
27
28
I
Address data lines [2:0]. These 3 address lines select one of the inter-
nal registers in UART channel A/B during a data bus transaction.
D7
D6
D5
D4
D3
D2
D1
D0
9
8
7
6
5
4
3
2
3
2
1
48
47
46
45
44
I/O
Data bus lines [7:0] (bidirectional).
IOR#
24
19
I
Input/Output Read Strobe (active low). The falling edge instigates an
internal read cycle and retrieves the data byte from an internal register
pointed to by the address lines [A2:A0]. The data byte is placed on the
data bus to allow the host processor to read it on the rising edge.
IOW#
20
15
I
Input/Output Write Strobe (active low). The falling edge instigates an
internal write cycle and the rising edge transfers the data byte on the
data bus to an internal register pointed by the address lines.
CSA#
16
10
I
UART channel A select (active low) to enable UART channel A in the
device for data bus operation.
CSB#
17
11
I
UART channel B select (active low) to enable UART channel B in the
device for data bus operation.
INTA
33
30
O
UART channel A Interrupt output. The output state is defined by the
user through the software setting of MCR[3]. INTA is set to the active
mode and OP2A# output is LOW when MCR[3] is set to a logic 1. INTA
is set to the three state mode and OP2A# is HIGH when MCR[3] is set
to a logic 0 (default). See MCR[3]. If this output is not used, leave it
unconnected.
INTB
32
29
O
UART channel B Interrupt output. The output state is defined by the
user through the software setting of MCR[3]. INTB is set to the active
mode and OP2B# output is LOW when MCR[3] is set to a logic 1. INTB
is set to the three state mode and OP2B# is HIGH when MCR[3] is set
to a logic 0 (default). See MCR[3]. If this output is not used, leave it
unconnected.
TXRDYA#
1
43
O
UART channel A Transmitter Ready (active low). The output
provides the TX FIFO/THR status for transmit channel A. See
Table 2. If this output is not used, leave it unconnected.
RXRDYA#
34
31
O
UART channel A Receiver Ready (active low). This output provides the
RX FIFO/RHR status for receive channel A. See
Table 2. If this output
is not used, leave it unconnected.
TXRDYB#
12
6
O
UART channel B Transmitter Ready (active low). The output provides
the TX FIFO/THR status for transmit channel B. See
Table 2. If this
output is not used, leave it unconnected.
相關PDF資料
PDF描述
ST16C554DIQ64-F IC UART FIFO 16B QUAD 64LQFP
XR16V554IV80-F IC UART FIFO 16B QUAD 80LQFP
XR16V554DIV-F IC UART FIFO 16B QUAD 64LQFP
ST16C554DCQ64-F IC UART FIFO 16B QUAD 64LQFP
ATMEGA164A-AUR IC MCU AVR 16K 20MHZ 44TQFP
相關代理商/技術參數
參數描述
XR16C2850CMTR-F 制造商:Exar Corporation 功能描述:UART 2-CH 128Byte FIFO 3.3V/5V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:XR16C2850CMTR-F
XR16C2850CP 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 128-byte FIFO’s AND RS-485 HALF DUPLEX CONTROL
XR16C2850CP40 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V AND 5V DUART WITH 128-BYTE FIFO
XR16C2850IJ 制造商:Exar Corporation 功能描述:UART 2-CH 128Byte FIFO 3.3V/5V 44-Pin PLCC 制造商:Rochester Electronics LLC 功能描述:
XR16C2850IJ44 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V AND 5V DUART WITH 128-BYTE FIFO
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*