- 您現在的位置：買賣IC網 > PDF目錄3766 > XR16C2850CM-F (Exar Corporation)IC UART FIFO 128B DUAL 48TQFP PDF資料下載
參數資料
| 型號： | XR16C2850CM-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 30/51頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 128B DUAL 48TQFP |
| 標準包裝： | 250 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 128 字節 |
| 規程： | RS232，RS485 |
| 電源電壓： | 2.97 V ~ 5.5 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-TQFP |
| 供應商設備封裝： | 48-TQFP（7x7） |
| 包裝： | 托盤 |
| 其它名稱： | 1016-1274 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
XR16C2850
xr
2.97V TO 5.5V DUAL UART WITH 128-BYTE FIFOS
REV. 2.1.3
36
EFR[5]: Special Character Detect Enable
Logic 0 = Special Character Detect Disabled (default).
Logic 1 = Special Character Detect Enabled. The UART compares each incoming receive character with
data in Xoff-2 register. If a match exists, the receive data will be transferred to FIFO and ISR bit-4 will be set
to indicate detection of the special character. Bit-0 corresponds with the LSB bit of the receive character. If
flow control is set for comparing Xon1, Xoff1 (EFR [1:0]= ‘10’) then flow control and special character work
normally. However, if flow control is set for comparing Xon2, Xoff2 (EFR[1:0]= ‘01’) then flow control works
normally, but Xoff2 will not go to the FIFO, and will generate an Xoff interrupt and a special character
interrupt, if enabled via IER bit-5.
EFR[6]: Auto RTS Flow Control Enable
RTS# output may be used for hardware flow control by setting EFR bit-6 to logic 1. When Auto RTS is
selected, an interrupt will be generated when the receive FIFO is filled to the programmed trigger level and
RTS de-asserts to a logic 1 at the next upper trigger level or hysteresis level. RTS# will return to a logic 0 when
FIFO data falls below the next lower trigger level. The RTS# output must be asserted (logic 0) before the auto
RTS can take effect. RTS# pin will function as a general purpose output when hardware flow control is
disabled.
Logic 0 = Automatic RTS flow control is disabled (default).
Logic 1 = Enable Automatic RTS flow control.
EFR[7]: Auto CTS Flow Control Enable
Automatic CTS Flow Control.
Logic 0 = Automatic CTS flow control is disabled (default).
Logic 1 = Enable Automatic CTS flow control. Data transmission stops when CTS# input de-asserts to logic
1. Data transmission resumes when CTS# returns to a logic 0.
4.20
Software Flow Control Registers (XOFF1, XOFF2, XON1, XON2) - Read/Write
These registers are used as the programmable software flow control characters xoff1, xoff2, xon1, and xon2.
For more details, see Table 6.
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C554DIQ64-F | IC UART FIFO 16B QUAD 64LQFP |
| XR16V554IV80-F | IC UART FIFO 16B QUAD 80LQFP |
| XR16V554DIV-F | IC UART FIFO 16B QUAD 64LQFP |
| ST16C554DCQ64-F | IC UART FIFO 16B QUAD 64LQFP |
| ATMEGA164A-AUR | IC MCU AVR 16K 20MHZ 44TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16C2850CMTR-F | 制造商:Exar Corporation 功能描述:UART 2-CH 128Byte FIFO 3.3V/5V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:XR16C2850CMTR-F |
| XR16C2850CP | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 128-byte FIFO’s AND RS-485 HALF DUPLEX CONTROL |
| XR16C2850CP40 | 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V AND 5V DUART WITH 128-BYTE FIFO |
| XR16C2850IJ | 制造商:Exar Corporation 功能描述:UART 2-CH 128Byte FIFO 3.3V/5V 44-Pin PLCC 制造商:Rochester Electronics LLC 功能描述: |
| XR16C2850IJ44 | 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V AND 5V DUART WITH 128-BYTE FIFO |
發布緊急采購，3分鐘左右您將得到回復。