- 您現在的位置：買賣IC網 > PDF目錄1974 > XR16C2850IM-F (Exar Corporation)IC UART FIFO 128B DUAL 48TQFP PDF資料下載
參數資料
| 型號： | XR16C2850IM-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 2/51頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 128B DUAL 48TQFP |
| 標準包裝： | 250 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 128 字節 |
| 規程： | RS232，RS485 |
| 電源電壓： | 2.97 V ~ 5.5 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-TQFP |
| 供應商設備封裝： | 48-TQFP（7x7） |
| 包裝： | 托盤 |
| 其它名稱： | 1016-1275 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
XR16C2850
xr
2.97V TO 5.5V DUAL UART WITH 128-BYTE FIFOS
REV. 2.1.3
10
2.7
INTA and INTB Ouputs
The INTA and INTB interrupt output output changes according to the operating mode and enahnced features
setup. Table 3 and 4 summarize the operating behavior for the transmitter and receiver. Also see Figures 20
through 25.
2.8
Crystal Oscillator or External Clock Input
The 2850 includes an on-chip oscillator (XTAL1 and XTAL2) to produce a clock for both UART sections in the
device. The CPU data bus does not require this clock for bus operation. The crystal oscillator provides a
system clock to the Baud Rate Generators (BRG) section found in each of the UART. XTAL1 is the input to the
oscillator or external clock buffer input with XTAL2 pin being the output. SEE”PROGRAMMABLE BAUD
FIGURE 4. TYPICAL OSCILLATOR CONNECTIONS
The on-chip oscillator is designed to use an industry standard microprocessor crystal (parallel resonant,
fundamental frequency with 10-22 pF capacitance load, ESR of 20-120 ohms and 100 ppm frequency
tolerance) connected externally between the XTAL1 and XTAL2 pins (see Figure 4). Alternatively, an external
clock can be connected to the XTAL1 pin to clock the internal baud rate generator for standard or custom rates.
TABLE 3: INTA AND INTB PINS OPERATION FOR TRANSMITTER
Auto RS485
Mode
FCR BIT-0 = 0
(FIFO DISABLED)
FCR BIT-0 = 1
(FIFO ENABLED)
INTA/B Pin
NO
LOW = a byte in THR
HIGH = THR empty
LOW = FIFO above trigger level
HIGH = FIFO below trigger level or FIFO empty
INTA/B Pin
YES
LOW = a byte in THR
HIGH = transmitter empty
LOW = FIFO above trigger level
HIGH = FIFO below trigger level or transmitter empty
TABLE 4: INTA AND INTB PIN OPERATION FOR RECEIVER
FCR BIT-0 = 0
(FIFO DISABLED)
FCR BIT-0 = 1
(FIFO ENABLED)
INTA/B Pin
LOW = no data
HIGH = 1 byte
LOW = FIFO below trigger level
HIGH = FIFO above trigger level
C1
22-47 pF
C2
22-47 pF
Y1
1.8432 MHz
to
24 MHz
R1
0-120
(Optional)
R2
500Κ1Μ
XTAL1
XTAL2
相關PDF資料 |
PDF描述 |
|---|---|
| XR16C2852IJ-F | IC UART FIFO 128B 44PLCC |
| XR16C850IMTR-F | IC UART FIFO 128B 48TQFP |
| XR16C854IQ-F | IC UART FIFO 128B QUAD 100QFP |
| XR16C864IQ-F | IC UART FIFO 128B QUAD 100QFP |
| XR16L2450IJ-F | IC UART FIFO 1B DUAL 44PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16C2850IMTR-F | 制造商:Exar Corporation 功能描述:XR16C2850IMTR-F |
| XR16C2850IP | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 128-byte FIFO’s AND RS-485 HALF DUPLEX CONTROL |
| XR16C2850IP40 | 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V AND 5V DUART WITH 128-BYTE FIFO |
| XR16C2852 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V DUAL UART WITH 128-BYTE FIFOS |
| XR16C2852_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V DUAL UART WITH 128-BYTE FIFOS |
發布緊急采購，3分鐘左右您將得到回復。