- 您現在的位置：買賣IC網 > PDF目錄11831 > XR16C2852CJ-F (Exar Corporation)IC UART FIFO 128B 44PLCC PDF資料下載
參數資料
| 型號： | XR16C2852CJ-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 7/51頁 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 128B 44PLCC |
| 標準包裝： | 27 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 128 字節 |
| 規程： | RS232，RS485 |
| 電源電壓： | 2.97 V ~ 5.5 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 供應商設備封裝： | 44-PLCC（16.59x16.59） |
| 包裝： | 管件 |
| 其它名稱： | XR16C2852CJ-F-ND |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
xr
XR16C2852
REV. 2.1.1
2.97V TO 5.5V DUAL UART WITH 128-BYTE FIFOS
15
2.13
Auto RTS (Hardware) Flow Control
Automatic RTS hardware flow control is used to prevent data overrun to the local receiver FIFO. The RTS#
output is used to request remote unit to suspend/resume data transmission. The auto RTS flow control
features is enabled to fit specific application requirement (see Figure 11):
Enable auto RTS flow control using EFR bit-6.
The auto RTS function must be started by asserting RTS output pin (MCR bit-1 to logic 1 after it is enabled).
With the Auto RTS function enabled, the RTS# output pin will not be de-asserted (logic 1) when the receive
FIFO reaches the programmed trigger level, but will be de-asserted when the FIFO reaches the next trigger
level (See Table 10). The RTS# output pin will be asserted again after the FIFO is unloaded to the next trigger
level below the programmed trigger level. However, even under these conditions, the 2852 will continue to
accept data until the receive FIFO is full if the remote UART transmitter continues to send data.
Enable RTS interrupt through IER bit-6 (after setting EFR bit-4). The UART issues an interrupt when the
RTS# pin is de-asserted (LOW) during Auto RTS flow control mode: ISR bit-5 will be set to logic 1.
2.14
Auto RTS Hysteresis
The 2852 has a new feature that provides flow control trigger hysteresis while maintaining compatibility with
the XR16C850, ST16C650A and ST16C550 family of UARTs. With the Auto RTS function enabled, an
interrupt is generated when the receive FIFO reaches the programmed RX trigger level. The RTS# pin will not
be forced HIGH (RTS off) until the receive FIFO reaches the upper limit of the hysteresis level. The RTS# pin
will return LOW after the RX FIFO is unloaded to the lower limit of the hysteresis level. Under the above
described conditions, the 2852 will continue to accept data until the receive FIFO gets full. The Auto RTS
function is initiated when the RTS# output pin is asserted LOW (RTS On). Table 13 shows the complete
details for the Auto RTS# Hysteresis levels. Please note that this table is for programmable trigger levels only
(Table D). The hysteresis values for Tables A-C are the next higher and next lower trigger levels in the
corresponding table.
2.15
Auto CTS Flow Control
Automatic CTS flow control is used to prevent data overrun to the remote receiver FIFO. The CTS# input is
monitored to suspend/restart the local transmitter. The auto CTS flow control feature is selected to fit specific
application requirement (see Figure 11):
Enable auto CTS flow control using EFR bit-7.
With the Auto CTS function enabled, the UART will suspend transmission as soon as the stop bit of the
character in the Transmit Shift Register has been shifted out. Transmission is resumed after the CTS# input is
re-asserted (logic 0), indicating more data may be sent.
Enable CTS interrupt through IER bit-7 (after setting EFR bit-4). The UART issues an interrupt when the
CTS# pin is de-asserted (logic 1) during Auto CTS flow control mode: ISR bit-5 will be set to 1.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B71-IX-F2 | CONVERTER MOD DC/DC 12V 75W |
| MS27473T24F61PB | CONN PLUG 61POS STRAIGHT W/PINS |
| VE-B71-IX-F1 | CONVERTER MOD DC/DC 12V 75W |
| VE-B71-IW-F3 | CONVERTER MOD DC/DC 12V 100W |
| MS3102A28-15S | CONN RCPT 35POS BOX MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16C2852CJTR-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16C2852IJ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| XR16C2852IJ-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16C2852IJTR-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR-16C450CJ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UART |
發布緊急采購，3分鐘左右您將得到回復。