REV. 2.3.1 12 2.7 Internal Registers The 850 has a set of enhanced registers fo" />
參數資料
型號： XR16C850IMTR-F
廠商： Exar Corporation
文件頁數： 4/56頁
文件大小： 0K
描述： IC UART FIFO 128B 48TQFP
標準包裝： 1,500
特點： *
通道數： 1，UART
FIFO's： 128 字節
規程： RS485
電源電壓： 2.97 V ~ 5.5 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 48-TQFP
供應商設備封裝： 48-TQFP（7x7）
包裝： 帶卷 (TR)
XR16C850
xr
2.97V TO 5.5V UART WITH 128-BYTE FIFO
REV. 2.3.1
12
2.7
Internal Registers
The 850 has a set of enhanced registers for controlling, monitoring and data loading and unloading. The
configuration register set is compatible to those already available in the standard 16C550. These registers
function as data holding registers (THR/RHR), interrupt status and control registers (ISR/IER), a FIFO control
register (FCR), receive line status and control registers (LSR/LCR), modem status and control registers (MSR/
MCR), programmable data rate (clock) divisor registers (DLL/DLM), and a user accessible scractchpad register
(SPR).
Beyond the general 16C550 features and capabilities, the 850 offers enhanced feature registers (EMSR, TRG,
FC, FCTR, EFR, Xon/Xoff 1, Xon/Xoff 2) that provide automatic RTS and CTS hardware flow control, Xon/Xoff
software flow control, automatic RS-485 half-duplex direction output enable/disable, FIFO trigger level control,
and FIFO level counters. All the register functions are discussed in full detail later in “Section 3.0, UART
2.8
DMA Mode
The DMA Mode (a legacy term) in this document does not mean “Direct Memory Access” but refers to data
block transfer operation. The DMA mode affects the state of the RXRDY# A/B and TXRDY# A/B output pins.
The transmit and receive FIFO trigger levels provide additional flexibility to the user for block mode operation.
The LSR bits 5-6 provide an indication when the transmitter is empty or has an empty location(s) for more data.
The user can optionally operate the transmit and receive FIFO in the DMA mode (FCR bit-3=1). When the
transmit and receive FIFO are enabled and the DMA mode is disabled (FCR bit-3 = 0), the 850 activates the
interrupt output pin for each data transmit or receive operation. When DMA mode is enabled (FCR bit-3 = 1),
the user takes advantage of block mode operation by loading or unloading the FIFO in a block sequence
determined by the programmed trigger level. In this mode, the 850 sets the TXRDY# pin when the transmit
FIFO becomes full, and sets the RXRDY# pin when the receive FIFO becomes empty. The following table
shows their behavior.
TABLE 2: TXRDY# AND RXRDY# OUTPUTS IN FIFO AND DMA MODE
PINS
FCR BIT-0=0
(FIFO DISABLED)
FCR BIT-0=1 (FIFO ENABLED)
FCR Bit-3 = 0
(DMA Mode Disabled)
FCR Bit-3 = 1
(DMA Mode Enabled)
RXRDY# A/B
0 = 1 byte.
1 = no data.
0 = at least 1 byte in FIFO
1 = FIFO empty.
1 to 0 transition when FIFO reaches the trigger
level, or timeout occurs.
0 to 1 transition when FIFO empties.
TXRDY# A/B
0 = THR empty.
1 = byte in THR.
0 = FIFO empty.
1 = at least 1 byte in FIFO.
0 = FIFO has at least 1 empty location.
1 = FIFO is full.
相關PDF資料
PDF描述
XR16C854IQ-F IC UART FIFO 128B QUAD 100QFP
XR16C864IQ-F IC UART FIFO 128B QUAD 100QFP
XR16L2450IJ-F IC UART FIFO 1B DUAL 44PLCC
XR16L2550IJ-F IC UART FIFO 16B DUAL 44PLCC
XR16L2551IM-F IC UART FIFO 16B DUAL 48TQFP
相關代理商/技術參數
參數描述
XR16C850IP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UART|CMOS|DIP|40PIN|PLASTIC
XR16C850IQ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UART|CMOS|QFP|52PIN|PLASTIC
XR16C854 制造商:EXAR 制造商全稱:EXAR 功能描述:并轉串4串口擴展芯片
XR16C854CJ 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
XR16C854CJ-0A-EVB 功能描述:UART 接口集成電路 Supports C854 68 ld PLCC, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*