參數資料
型號: XR16C854D
廠商: Exar Corporation
英文描述: 2.97V TO 5.5V QUAD UART WITH 128-BYTE FIFO
中文描述: 2.97V至5.5V四路UART的128字節FIFO
文件頁數: 34/51頁
文件大?。?/td> 476K
代理商: XR16C854D
XR16C854
34
Rev. 1.00P
hardware flow control. -RTS functions normally when
hardware flow control is disabled.
0 = Automatic RTS flow control is disabled. (normal
default condition)
1 = Enable Automatic RTS flow control.
EFR bit-7:
Automatic CTS Flow Control.
Logic 0 = Automatic CTS flow control is disabled.
(normal default condition)
Logic 1 = Enable Automatic CTS flow control. Trans-
mission will stop when -CTS goes to a logical 1.
Transmission will resume when the -CTS pin returns
to a logical 0.
FIFO READY REGISTER
This register is applicable to 100 pin XR16C854s only.
The FIFO resister provides the real time status of the
transmit and receive FIFOs. Each TX and RX cannel
(A-D) has its own 128 byte FIFO. When any of the
eight TX/RX FIFOs become full, a bit associated with
its TX/RX function and channel A-D is set in the FIFO
status register.
FIFO channel A-D RDY Bit 0-3:
0 = The transmit FIFO A-D associated with this bit is
full. This channel will not accept any more transmit
data.
1 = One or more empty locations exist in the FIFO.
FIFORdy Bit 4-7:
0 = The receive FIFO is above the programmed
trigger level or time-out is occurred.
1 = Receiver is ready and is below the programmed
trigger level.
FEATURE CONTROL REGISTER
This register controls the XR16C854 new functions
that are not available on ST16C550 or ST16C650.
FCTR BIT 0-1:
User selectable -RTS delay timer for hardware flow
control application. After reset, these bits are set to 0
to select the next trigger level for hardware flow
control.
FCTR
Bit-1
FCTR
Bit-0
Trigger
level
0
0
Next trigger
level
4 word+trigger level
6 word+trigger level
8 word+trigger level
0
1
1
1
0
1
FCTR BIT-2:
0 = Select RX input as encoded IrDa data.
1 = Select RX input as active high encoded IrDa data.
FCTR BIT-3:
Interrupt type select.
0 = Standard ST16C550 mode. Transmitter generates
interrupt when transmit holding register is empty and
transmit shift register is shifting data out.
1 = Transmit empty interrupt. Transmit interrupt is
generated when transmit holding and shift register is
empty.
FCTR BIT 4-5:
Transmit / receive trigger table select.
FCTR
Bit-5
FCTR
Bit-4
Table
0
0
1
1
0
1
0
1
Table-A (TX/RX)
Table-B (TX/RX)
Table-C (TX/RX)
Table-D (TX/RX)
FCTR BIT-6:
Register mode select.
0 = Scratch Pad register is selected as general read
and write register. ST16C550 compatible mode.
1 = FIFO count register, Enhanced Mode Select
Register. Number of characters in transmit or receive
holding register can be read via scratch pad register
when this bit is set. Enhanced Mode is selected when
it is written into it.
相關PDF資料
PDF描述
XR16C864 Quad UART with RX/TX FIFO Counters and 128-byte FIFO(四通用異步接收器/發送器(帶RX/TX 先進先出計數器和128字節先進先出))
XR16C872 Dual UART with 1284 Parallel Port and Plug-and-Play(PnP) Controller(雙通用異步接收器/發送器(帶1284雙向并行端口和即插即用控制器))
XR16L2450 2.25V TO 5.5V DUART
XR16L2450IJ 97-3108A20-29S-KIT
XR16L2450IM 2.25V TO 5.5V DUART
相關代理商/技術參數
參數描述
XR16C854DCV 制造商:Exar Corporation 功能描述:
XR16C854DCV-0A-EB 功能描述:UART 接口集成電路 Supports C854D 64 ld TQFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16C854DCV-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16C854DCVTR-F 制造商:Exar Corporation 功能描述:UART 4-CH 128Byte FIFO 3.3V/5V 64-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR16C854DCVTR-F
XR16C854DIV 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V QUAD UART WITH 128-BYTE FIFO