- 您現在的位置：買賣IC網 > PDF目錄376454 > XR16C854IV (EXAR CORP) APH97-3108A20-29S PDF資料下載
參數資料
| 型號： | XR16C854IV |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | APH97-3108A20-29S |
| 中文描述： | 4 CHANNEL(S), 2M bps, SERIAL COMM CONTROLLER, PQFP64 |
| 封裝： | 10 X 10 MM, 1.40 MM HEIGHT, TQFP-64 |
| 文件頁數： | 18/51頁 |
| 文件大小： | 476K |
| 代理商： | XR16C854IV |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
XR16C854
18
Rev. 1.00P
C1
22pF
C2
33pF
X1
1.8432 MHz
X
X
Figure 8, Crystal oscillator connection
Hardware/Software and Timeout Interrupts
Three special interrupts have been added to monitor
the hardware and software flow control. The interrupts
are enabled by IER bits 5-7. Care must be taken when
handling these interrupts. Following a reset the trans-
mitter interrupt is enabled, the 854 will issue an
interrupt to indicate that transmit holding register is
empty. This interrupt must be serviced prior to con-
tinuing operations. The LSR register provides the
current singular highest priority interrupt only. It could
be noted that CTS and RTS interrupts have lowest
interrupt priority. A condition can exist where a higher
priority interrupt may mask the lower priority CTS/
RTS interrupt(s). Only after servicing the higher pend-
ing interrupt will the lower priority CTS/ RTS
interrupt(s) be reflected in the status register. Servic-
ing the interrupt without investigating further interrupt
conditions can result in data errors.
When two interrupt conditions have the same priority,
it is important to service these interrupts correctly.
Receive Data Ready and Receive Time Out have the
same interrupt priority (when enabled by IER bit-3).
The receiver issues an interrupt after the number of
characters have reached the programmed trigger
level. In this case the 854 FIFO may hold more
characters than the programmed trigger level. Follow-
ing the removal of a data byte, the user should recheck
LSR bit-0 for additional characters. A Receive Time
Out will not occur if the receive FIFO is empty. The
time out counter is reset at the center of each stop bit
received or each time the receive holding register
(RHR) is read. The actual time out value is T (
T
ime out
length in bits) = 4 X P (
P
rogrammed word length) + 12.
To convert the time out value to a character value, the
user has to consider the complete word length, includ-
ing data information length, start bit, parity bit, and the
size of stop bit, i.e., 1X, 1.5X, or 2X bit times.
Example -A: If the user programs a word length of 7,
with no parity and one stop bit, the time out will be:
T = 4 X 7( programmed word length) +12 = 40 bit times.
The character time will be equal to 40 / 9 = 4.4
characters, or as shown in the fully worked out ex-
ample: T = [(programmed word length = 7) + (stop bit
= 1) + (start bit = 1) = 9]. 40 (bit times divided by 9) =
4.4 characters.
Example -B: If the user programs the word length = 7,
with parity and one stop bit, the time out will be:
T = 4 X 7(programmed word length) + 12 = 40 bit times.
Character time = 40 / 10 [ (programmed word length
= 7) + (parity = 1) + (stop bit = 1) + (start bit = 1) = 4
characters.
In the 16 mode for 68/100 pin packages, the system/
board designer can optionally provide software con-
trolled three state interrupt operation. This is accom-
plished by INTSEL and MCR bit-3. When INTSEL
interface pin is left open or made a logic 0, MCR bit-
3 controls the three state interrupt outputs, INT A-D.
When INTSEL is a logic 1, MCR bit-3 has no effect on
the INT A-D outputs and the package operates with
interrupt outputs enabled continuously.
Programmable Baud Rate Generator
The 854 supports high speed modem technologies
that have increased input data rates by employing
data compression schemes. For example a 33.6Kbps
modem that employs data compression may require a
115.2Kbps input data rate. A 128.0Kbps ISDN modem
that supports data compression may need an input
data rate of 460.8Kbps. The 854 can support a stan-
dard data rate of 921.6Kbps.
相關PDF資料 |
PDF描述 |
|---|---|
| XR16C854D | 2.97V TO 5.5V QUAD UART WITH 128-BYTE FIFO |
| XR16C864 | Quad UART with RX/TX FIFO Counters and 128-byte FIFO(四通用異步接收器/發送器（帶RX/TX 先進先出計數器和128字節先進先出）) |
| XR16C872 | Dual UART with 1284 Parallel Port and Plug-and-Play（PnP） Controller(雙通用異步接收器/發送器（帶1284雙向并行端口和即插即用控制器）) |
| XR16L2450 | 2.25V TO 5.5V DUART |
| XR16L2450IJ | 97-3108A20-29S-KIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16C854IV-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16C854IV-F | 制造商:Exar Corporation 功能描述:IC QUAD UART 2MBPS 5.5V 64-LQFP |
| XR16C854IVTR-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16C864 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V QUAD UART WITH 128-BYTE FIFO |
| XR16C864CQ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。