REV. 1.1.1 2.25V TO 5.5V DUART 7 2.4 Device Identification and Revision The L2450 provides a Device Identification code and a Devi" />
參數資料
型號: XR16L2450IJ-F
廠商: Exar Corporation
文件頁數: 28/30頁
文件大?。?/td> 0K
描述: IC UART FIFO 1B DUAL 44PLCC
標準包裝: 27
特點: *
通道數: 2,DUART
FIFO's: 1 字節
規程: RS232
電源電壓: 2.25 V ~ 5.5 V
帶故障啟動位檢測功能:
帶調制解調器控制功能:
帶CMOS:
安裝類型: 表面貼裝
封裝/外殼: 44-LCC(J 形引線)
供應商設備封裝: 44-PLCC(16.59x16.59)
包裝: 管件
xr
XR16L2450
REV. 1.1.1
2.25V TO 5.5V DUART
7
2.4
Device Identification and Revision
The L2450 provides a Device Identification code and a Device Revision code to distinguish the part from other
devices and revisions. To read the identification code from the part, it is required to set the baud rate generator
registers DLL and DLM both to 0x00. Now reading the content of the DLM will provide 0x02 to indicate L2450
and reading the content of DLL will provide the revision of the part; for example, a reading of 0x01 means
revision A.
2.5
Channel A and B Selection
The UART provides the user with the capability to bi-directionally transfer information between an external
CPU and an external serial communication device. A logic 0 on chip select pins, CSA# or CSB#, allows the
user to select UART channel A or B to configure, send transmit data and/or unload receive data to/from the
UART. Selecting both UARTs can be useful during power up initialization to write to the same internal registers,
but do not attempt to read from both uarts simultaneously. Individual channel select functions are shown in
2.6
Channel A and B Internal Registers
Each UART channel in the L2450 has a standard register set for controlling, monitoring and data loading and
unloading. These registers function as data holding registers (THR/RHR), interrupt status and control registers
(ISR/IER), receive line status and control registers (LSR/LCR), modem status and control registers (MSR/
MCR), programmable data rate (clock) divisor registers (DLL/DLM), and a user accessible scratch pad register
(SPR).
2.7
INTA and INTB Outputs
The INTA and INTB interrupt output changes according to the operating mode and enhanced features setup.
Table 2 summarizes the operating behavior for the transmitter and receiver. Also see Figure 12 and Figure 13.
2.8
Crystal Oscillator or External Clock Input
The L2450 includes an on-chip oscillator (XTAL1 and XTAL2) to produce a clock for both UART sections in the
device. The CPU data bus does not require this clock for bus operation. The crystal oscillator provides a
system clock to the Baud Rate Generators (BRG) section found in each of the UART. XTAL1 is the input to the
oscillator or external clock buffer input with XTAL2 pin being the output. For programming details, see
“Programmable Baud Rate Generator.”
TABLE 1: CHANNEL A AND B SELECT
CSA#
CSB#
FUNCTION
1
UART de-selected
0
1
Channel A selected
1
0
Channel B selected
0
Channel A and B selected
TABLE 2: INTA AND INTB PINS OPERATION FOR TRANSMITTER
TRANSMITTER
RECEIVER
INTA/B Pin
0 = a byte in THR
1 = THR empty
0 = no data
1 = 1 byte
相關PDF資料
PDF描述
XR16L2550IJ-F IC UART FIFO 16B DUAL 44PLCC
XR16L2551IM-F IC UART FIFO 16B DUAL 48TQFP
XR16L2552IJ-F IC UART FIFO 16B DUAL 44PLCC
XR16L2750IJ-F IC UART FIFO 64B DUAL 44PLCC
XR16L2751CMTR-F IC UART FIFO 64B DUAL 48TQFP
相關代理商/技術參數
參數描述
XR16L2450IM 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART
XR16L2450IM-0A-EB 功能描述:UART 接口集成電路 Supports L2450 48 ld TQFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L2450IM-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L2550 制造商:EXAR 制造商全稱:EXAR 功能描述:LOW VOLTAGE DUART WITH 16-BYTE FIFO
XR16L2550_07 制造商:EXAR 制造商全稱:EXAR 功能描述:LOW VOLTAGE DUART WITH 16-BYTE FIFO