- 您現在的位置：買賣IC網 > PDF目錄376454 > XR16L2550 (Exar Corporation) LOW VOLTAGE DUART WITH 16-BYTE FIFO PDF資料下載
參數資料
| 型號： | XR16L2550 |
| 廠商： | Exar Corporation |
| 英文描述： | LOW VOLTAGE DUART WITH 16-BYTE FIFO |
| 中文描述： | 低壓杜阿爾特16字節FIFO |
| 文件頁數： | 29/45頁 |
| 文件大小： | 278K |
| 代理商： | XR16L2550 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
á
REV. 1.0.0
XR16L2550
LOW VOLTAGE DUART WITH 16-BYTE FIFO
29
MCR[3]: OP2# Output / INT Output Enable
This bit enables and disables the operation of INT, interrupt output. If INT output is not used, OP2# can be used
as a general purpose output.
Logic 0 = INT (A-B) outputs disabled (three state mode) and OP2# output set to a logic 1 (default).
Logic 1 = INT (A-B) outputs enabled (active mode) and OP2# output set to a logic 0.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and
Figure 13
.
MCR[5]: Xon-Any Enable
Logic 0 = Disable Xon-Any function (for 16C550 compatibility, default).
Logic 1 = Enable Xon-Any function. In this mode, any RX character received will resume transmit operation.
The RX character will be loaded into the RX FIFO , unless the RX character is an Xon or Xoff character and
the L2552 is programmed to use the Xon/Xoff flow control.
MCR[6]: Infrared Encoder/Decoder Enable
Logic 0 = Enable the standard modem receive and transmit input/output interface. (Default)
Logic 1 = Enable infrared IrDA receive and transmit inputs/outputs. The TX/RX output/input are routed to the
infrared encoder/decoder. The data input and output levels conform to the IrDA infrared interface
requirement. While in this mode, the infrared TX output will be a logic 0 during idle data conditions.
MCR[7]: Clock Prescaler Select
Logic 0 = Divide by one. The input clock from the crystal or external clock is fed directly to the Programmable
Baud Rate Generator without further modification, i.e., divide by one (default).
Logic 1 = Divide by four. The prescaler divides the input clock from the crystal or external clock by four and
feeds it to the Programmable Baud Rate Generator, hence, data rates become one forth.
3.8
Line Status Register (LSR) - Read Only
This register provides the status of data transfers between the UART and the host.
LSR[0]: Receive Data Ready Indicator
Logic 0 = No data in receive holding register or FIFO (default).
Logic 1 = Data has been received and is saved in the receive holding register or FIFO.
LSR[1]: Receiver Overrun Flag
Logic 0 = No overrun error (default).
Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens
when additional data arrives while the FIFO is full. In this case the previous data in the receive shift register is
overwritten. Note that under this condition the data byte in the receive shift register is not transferred into the
FIFO, therefore the data in the FIFO is not corrupted by the error. An interrupt will be generated immediately
if LSR interrupt is enabled (IER bit-2).
LSR[2]: Receive Data Parity Error Flag
Logic 0 = No parity error (default).
Logic 1 = Parity error. The receive character in RHR does not have correct parity information and is suspect.
This error is associated with the character available for reading in RHR. If the LSR interrupt is enabled (IER
bit-2), an interrupt will be generated when the character is in the RHR.
相關PDF資料 |
PDF描述 |
|---|---|
| XR16L2551 | LOW VOLTAGE DUART WITH POWERSAVE |
| XR16L2551IL | LOW VOLTAGE DUART WITH POWERSAVE |
| XR16L2551IM | LOW VOLTAGE DUART WITH POWERSAVE |
| XR16L2552IJ | 2.25V TO 5.5V DUART WITH 16-BYTE FIFO |
| XR16L2552IM | 2.25V TO 5.5V DUART WITH 16-BYTE FIFO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16L2550_07 | 制造商:EXAR 制造商全稱:EXAR 功能描述:LOW VOLTAGE DUART WITH 16-BYTE FIFO |
| XR16L2550IJ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| XR16L2550IJ-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L2550IL | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L2550IL-0A-EB | 功能描述:UART 接口集成電路 Supports L2550 32pin QFN, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。